Bob_Belville Posted October 4, 2018 Report Share Posted October 4, 2018 Using V speeds for take off and climb: Vx, best angle of climb, initial climb, gear up Vy, best rate of climb, accelerate to Vy and raise TO flaps Vcc, cruise climb, not in POH but use difference between Vx and Vy. E.g., my E has Vx (clean) is 82 kias, Vy (clean) is 91 kias, so Vcc is 100 kias. You might have to use a higher Vcc for a long climb on a hot day but Bob suggests his rule of thumb is most efficient. 1 Quote Link to comment Share on other sites More sharing options...
MIm20c Posted October 4, 2018 Report Share Posted October 4, 2018 I came away with him saying it was most efficient to retract flaps at Vy and safest to put some extra distance from the ground as quickly as possible. However, I didn’t get the feeling he wanted everyone to use Vy all the way up. Quote Link to comment Share on other sites More sharing options...
Hank Posted October 4, 2018 Report Share Posted October 4, 2018 Personally, I've almost always used Vx until clear of obstacles, then Vy to altitude. When I'm heavy, the runway is short and / or the obstacles high, I use Takeoff Flaps, and retract them when I'm looking down at the obstacles. Gear goes up once I'm in the air and in good control (per the Owners Manual). Works well for my C . . . . Quote Link to comment Share on other sites More sharing options...
201er Posted October 4, 2018 Report Share Posted October 4, 2018 47 minutes ago, Bob_Belville said: E.g., my E has Vx (clean) is 82 kias, Vy (clean) is 91 kias, so Vcc is 100 kias. You might have to use a higher Vcc for a long climb on a hot day but Bob suggests his rule of thumb is most efficient. That Vx number sounds a bit off, you sure about that? Quote Link to comment Share on other sites More sharing options...
Hank Posted October 4, 2018 Report Share Posted October 4, 2018 3 minutes ago, 201er said: That Vx number sounds a bit off, you sure about that? Bob's numbers for the E are significantly higher than for my C below: Vx = 80 mph = 70 KIAS Vy = 100 mph - Altitude in thousands = 87 KIAS - Altitude Cruise Climb is to 115--120 mph = 100--104 KIAS. But his E is heavier and has a little more power, about 10% or so. Quote Link to comment Share on other sites More sharing options...
orionflt Posted October 4, 2018 Report Share Posted October 4, 2018 VX in the E is 80 MPH/70 KIAS VY=105 MPH/91 KIAS 1 Quote Link to comment Share on other sites More sharing options...
skydvrboy Posted October 4, 2018 Report Share Posted October 4, 2018 I know each model is different, but for my F, Vx is 94 mph (82 kts) and Vy is 113 mph (98 kts) at sea level decreasing to 102 mph (89 kts). So that would make my initial cruise climb be 132. Seems a bit fast, so climb would be slow, but you'd cover a lot of ground getting there. Quote Link to comment Share on other sites More sharing options...
tigers2007 Posted October 4, 2018 Report Share Posted October 4, 2018 How do you guys account for airspeed indicator error while trying to maintain Vcc while climbing to high altitudes?Sent from my iPhone using Tapatalk Quote Link to comment Share on other sites More sharing options...
skydvrboy Posted October 4, 2018 Report Share Posted October 4, 2018 6 minutes ago, tigers2007 said: How do you guys account for airspeed indicator error while trying to maintain Vcc while climbing to high altitudes? I don't. I use IAS and if I don't like the climb rate, CHT's, or Oil temps, I adjust accordingly. 2 Quote Link to comment Share on other sites More sharing options...
Bob_Belville Posted October 4, 2018 Author Report Share Posted October 4, 2018 Very few of these V speeds are shown in the 1966 Owners Manual. And I won't swear they are all correct: Other, unmarked Airspeeds: mph kts Vlg 120 104 Va mgw 132 115 Va 2200# 122 106 Vx (to flaps) 80 70 Vy (to flaps) 95 83 Vx clean 94 82 Vy clean 105 91 Vg mgw 105 91 Vg 2200# 97 84 V window 150 130 V autopilot 170 148 V spdbrk 1.3Vso 75 65 1.3Vs 87 76 1 Quote Link to comment Share on other sites More sharing options...
Bob_Belville Posted October 4, 2018 Author Report Share Posted October 4, 2018 22 minutes ago, bluehighwayflyer said: So 92.5 MPH? Sorry, but that is too slow for cruise climb. Not even close. I used to use 120 MPH in the J. With the C I’ll start out with 110 MPH and see how the temperatures behave. Jim Jim, 100 kias is 115 mias. That's pretty close to your 120 mias. Quote Link to comment Share on other sites More sharing options...
Bob_Belville Posted October 4, 2018 Author Report Share Posted October 4, 2018 37 minutes ago, orionflt said: VX in the E is 80 MPH/70 KIAS VY=105 MPH/91 KIAS Are you comparing TO flaps to clean? I show 70 kias as Vx TO flaps. 91 kias is clean. Quote Link to comment Share on other sites More sharing options...
DualRatedFlyer Posted October 4, 2018 Report Share Posted October 4, 2018 3 hours ago, bluehighwayflyer said: Hi, Bob. I was basing my comment on @orionflt‘s quoted M20E IASs of 80 MPH for Vx and 105 MPH for Vy. The average between them would be 92.5 MPH IAS which is just too slow of a cruise climb speed in any four cylinder Lycoming powered Mooney for good cooling, and especially so for the older models with less efficient cowlings. Or perhaps I misunderstood either his or your posts? EDIT. Yes, your 115 MIAS would be about right. Jim You take the difference between the two, then add that number to Vy to get Vcc. According to Orionflt's numbers Vy 105 - Vx 80 = 25. Take Vy and add 25 to it and you get a Vcc of 130mph https://www.flyingmag.com/technique/tip-week/calculating-cruise-climb-speed Quote Link to comment Share on other sites More sharing options...
bradp Posted October 4, 2018 Report Share Posted October 4, 2018 Seems like Vcc is close to Vz. 2 Quote Link to comment Share on other sites More sharing options...
Danb Posted October 4, 2018 Report Share Posted October 4, 2018 105-85=20+105=125 therefore Vcc is 125. I’ve generally climbed at 120 depending on temps. Many times my cruise climb approximates 130 which is a nice tradeoff. Again temps are supreme. Especially when at a safe altitude. I was totally enveloped in Bob K’s talk, a world of knowledge provided to us within an hour, clearly one of the best INO of all the speakers, although Dan’s recap of his venture with co2 was riveting I could listen to both of them all day. Quote Link to comment Share on other sites More sharing options...
jetdriven Posted October 4, 2018 Report Share Posted October 4, 2018 3 hours ago, bradp said: Seems like Vcc is close to Vz. @testwest wrote a whole Thesis paper about Vz climb. That’s the speed to use. 3 Quote Link to comment Share on other sites More sharing options...
mike_elliott Posted October 4, 2018 Report Share Posted October 4, 2018 Bob Kromer and I have talked a number of times about the best[1] way to climb in a Mooney. As others have said so eloquently, Temps are a limiting, but not necessarily THE governing factor. Obstacles are primary with Temps secondary. Get out of the kill zone quickly (below 800'), then set up for cruise climb. 160 of you saw this slide last Saturday. [1] Everyone has their idea of best way, this is the way I subscribe as does a number of Mooney CFI's and engineering test pilots. The POH should govern the operation of your aircraft. 6 1 Quote Link to comment Share on other sites More sharing options...
L. Trotter Posted October 4, 2018 Report Share Posted October 4, 2018 I would really like to have Bob Kromer back next year to provide further enlightenment. 2 Quote Link to comment Share on other sites More sharing options...
orionflt Posted October 4, 2018 Report Share Posted October 4, 2018 10 hours ago, Bob_Belville said: Are you comparing TO flaps to clean? I show 70 kias as Vx TO flaps. 91 kias is clean. I just pulled the numbers out of the "66 E poh, the info was limited but the Vx number is TO flaps because if you are doing a Vx climb over an obstacle you would not retract your flap and would not use a clean configuration for take off. Brian Quote Link to comment Share on other sites More sharing options...
jlunseth Posted October 4, 2018 Report Share Posted October 4, 2018 I do my climb out the same way, but came at it through different calculations. Vx is 71 kts, and Vy is 96, so my theoretical “Vz” is 83.5. That’s approximately the number I use but my number is based on an article in AOPA magazine a few years ago. The author actually ran a series of tests of what would happen in the event of engine loss on departure. Vx was not best for two reasons. First, they concluded that on average, a pilot does nothing for at least three seconds after engine failure, and in the attitude required to make Vx, the loss of airspeed is too high, the aircraft gets too close to Vs. Vy was not best because it took too much time and distance to get to turn-back altitude. You could make the necessary 270 turn without screwing it into the ground, but could not make the airport. They found best glide was best. So that is what I use, best glide. Best glide varies in my aircraft with gross weight from 81 to 85, I just use 85. The plane accelerates to best glide pretty quickly once I get the gear and flaps up, I don’t wait with that any longer than necessary to get a positive climb rate. Turns out best glide is useful for all kinds of things. It provides a good deal of margin from stall, so during takeoff and climb out, in the event of some kind of weather anamoly that causes airspeed to instantaneously drop, I am still a good 10 kts. above stall. Base, and base to final, it gives me a buffer from a steep bank stall in the event of a too tight turn. I would stall at 60 degrees, but not at anything reasonable. So far, it has worked good. 1 Quote Link to comment Share on other sites More sharing options...
Bob_Belville Posted October 4, 2018 Author Report Share Posted October 4, 2018 1 minute ago, orionflt said: I just pulled the numbers out of the "66 E poh, the info was limited but the Vx number is TO flaps because if you are doing a Vx climb over an obstacle you would not retract your flap and would not use a clean configuration for take off. Brian Brian, I agree with that operating procedure. But I suppose when we're looking for a delta airspeed between Vx and Vy to calculate Vcc we need to compare clean to clean which is 9 kts instead of 21 kts. So... Vcc is 100 kts instead of 113 kts. Actually, I usually climb at 115 to 120 kts but that results in 400 +/- ft/min climb. I'm going to try the 100 kts for a better climb rate and see if I can live with the temps. Of course Kromer is suggesting this as a rule of thumb to be rounded off and tweaked based on experimentation. 1 Quote Link to comment Share on other sites More sharing options...
orionflt Posted October 4, 2018 Report Share Posted October 4, 2018 1 minute ago, Bob_Belville said: Brian, I agree with that operating procedure. But I suppose when we're looking for a delta airspeed between Vx and Vy to calculate Vcc we need to compare clean to clean which is 9 kts instead of 21 kts. So... Vcc is 100 kts instead of 113 kts. Actually, I usually climb at 115 to 120 kts but that results in 400 +/- ft/min climb. I'm going to try the 100 kts for a better climb rate and see if I can live with the temps. Of course Kromer is suggesting this as a rule of thumb to be rounded off and tweaked based on experimentation. I am flying a '61 C and my numbers are similar to your E but my flight manual has a lot less information on airspeed and performance, the one thing mine does state is to use 95 MPH on climb out. that actually works well for me and is what I use initially before transitioning to 120 MPH after i'm around 1000ft AGL. I also know the Early E's were using the same numbers but if memory serves me correctly, later models were using 105 MPH (also best glide speed) as the target number. Quote Link to comment Share on other sites More sharing options...
mike_elliott Posted October 4, 2018 Report Share Posted October 4, 2018 Bob is a board member of the Mooney Summit, Inc. and work permitting, will be in attendance. Bob's passion is Mooney. We are so fortunate to have him, Ken Yale, Ron Dubin, Seth Meyers and Lee Drumheller as board members. I am honored to have these fine gents as colleagues to help better the breed. Of all the board of directors I have served on over the years, this is without a doubt, the finest. 6 Quote Link to comment Share on other sites More sharing options...
Bob_Belville Posted October 4, 2018 Author Report Share Posted October 4, 2018 6 minutes ago, jlunseth said: I do my climb out the same way, but came at it through different calculations. Vx is 71 kts, and Vy is 96, so my theoretical “Vz” is 83.5. That’s approximately the number I use but my number is based on an article in AOPA magazine a few years ago. The author actually ran a series of tests of what would happen in the event of engine loss on departure. Vx was not best for two reasons. First, they concluded that on average, a pilot does nothing for at least three seconds after engine failure, and in the attitude required to make Vx, the loss of airspeed is too high, the aircraft gets too close to Vs. Vy was not best because it took too much time and distance to get to turn-back altitude. You could make the necessary 270 turn without screwing it into the ground, but could not make the airport. They found best glide was best. So that is what I use, best glide. Best glide varies in my aircraft with gross weight from 81 to 85, I just use 85. The plane accelerates to best glide pretty quickly once I get the gear and flaps up, I don’t wait with that any longer than necessary to get a positive climb rate. Turns out best glide is useful for all kinds of things. It provides a good deal of margin from stall, so during takeoff and climb out, in the event of some kind of weather anamoly that causes airspeed to instantaneously drop, I am still a good 10 kts. above stall. Base, and base to final, it gives me a buffer from a steep bank stall in the event of a too tight turn. I would stall at 60 degrees, but not at anything reasonable. So far, it has worked good. For my E, Vy and Vg (at gross) are both 91 kts. I round to 90 kts as my best climb or descent ias. (If i'm alone Vg is closer to 85.) 1 Quote Link to comment Share on other sites More sharing options...
jlunseth Posted October 4, 2018 Report Share Posted October 4, 2018 Amazing. Mass agreement in the forum. Now, are you climbing leaned out or full rich..... 2 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.