Oscar Avalle Posted January 21, 2017 Report Posted January 21, 2017 Well I feel like a real idiot! My overhauled fuel selector valve needed to be adjusted...(the fuel drainer was leaking a little bit). So I asked my AP to look into it. Yesterday I decided that it was a great idea to help... My office was closed because of the inauguration. I cleaned it and I told the AP that I would reinstall the valve. I over tighten the screw on the little cup below the assembly and I broke the valve! Now I need a replacement. Not easy to get the original one! Is their a replacement...??? Luckily I was able to find a used one on eBay...us$ 423... hope it is serviceable. Anyway, long story short... I tried to help being CB... and now I don't even know what it may cost me... Oscar 2 Quote
Marauder Posted January 21, 2017 Report Posted January 21, 2017 I feel your pain!Sent from my iPad using Tapatalk 1 Quote
tony Posted January 21, 2017 Report Posted January 21, 2017 Just think of the educational experience. You wont over tighten it again...... We've all been there done that Oscar. That's happened to me once or twice. 3 Quote
MyNameIsNobody Posted January 21, 2017 Report Posted January 21, 2017 Did I tell you about the one where I was trying to access the accessory belt in my Cayman S and I stripped the torn nut on a trim piece? So I had to buy tools to get the stripped round head nut out after going all over town to find a "better sized" torx driver... (That was just the one last week) Oh yes Oscar I have been "there".... 2 Quote
DAVIDWH Posted January 21, 2017 Report Posted January 21, 2017 Don't beat yourself up. You just did a normal thing. It's in our DNA to turn the screw, nut or bolt one more time, just to be sure. And, although we have torque wrenches for nuts and bolts, not yet a torque indicator for the common screwdriver. Too bad we lost Steve Jobs. Best, 2 Quote
prflyer Posted January 21, 2017 Report Posted January 21, 2017 Sorry Oscar. I saw your airplane yesterday afternoon in the hangar while I was talking with Frans and wondered what was going on. Fernando Quote
LANCECASPER Posted January 21, 2017 Report Posted January 21, 2017 2 hours ago, DAVIDWH said: Don't beat yourself up. You just did a normal thing. It's in our DNA to turn the screw, nut or bolt one more time, just to be sure. And, although we have torque wrenches for nuts and bolts, not yet a torque indicator for the common screwdriver. Too bad we lost Steve Jobs. Best, There are a few options for torque screwdrivers: https://www.grainger.com/category/torque-screwdrivers/screwdrivers-and-nutdrivers/tools/ecatalog/N-166c https://www.wihatools.com/torque-control-drivers-handles-blades/torquecontrol-tools No need to feel like an idiot, look at it this way, you have an opportunity to buy a new tool. 1 Quote
MyNameIsNobody Posted January 21, 2017 Report Posted January 21, 2017 3 hours ago, LANCECASPER said: There are a few options for torque screwdrivers: https://www.grainger.com/category/torque-screwdrivers/screwdrivers-and-nutdrivers/tools/ecatalog/N-166c https://www.wihatools.com/torque-control-drivers-handles-blades/torquecontrol-tools No need to feel like an idiot, look at it this way, you have an opportunity to buy a new tool. PORSCHE was having a bad day. Those screws were sketchy. Replacements were four bucks and fit perfectly... 1 Quote
Yetti Posted January 22, 2017 Report Posted January 22, 2017 (edited) There is an SB to change the toque value that is written on some valves to a lower value so things like this don't happen. Edited January 22, 2017 by Yetti 1 Quote
Gary0747 Posted January 22, 2017 Report Posted January 22, 2017 I think mine has a torque value of only 25 inch pounds printed right on it. Not much so dont forget the safety wire or you dont want to think about the consequences. Quote
Guest Posted January 22, 2017 Report Posted January 22, 2017 Here is the SB in question. http://www.mooney.com/en/sb/M20-200.pdf Clarence Edit, Has anyone ever installed a Helicoil to repair the stripped thread? Quote
carusoam Posted January 22, 2017 Report Posted January 22, 2017 If we are talking about the single bolt in the center of the fuel bowl... My 65C had what looked like a stainless bolt in it. It suffered from a corrosion issue that looked like a bite of an apple right about where the screen was. As far as breaking things goes... on my first owner assisted annual, I asked the mechanics if they would mind me helping. They said I was welcomed to do as much as I was comfortable with. The chances of me breaking something would far outweigh the the amount of work I would take away from them... Knowing that, I tried to be as careful as possible when opening and closing things up. Buying new tools from the truck each year. I still wrecked a lot of screws, but now I have a fancy left handed drill bit and a handy really thin pair of pliers with a good grip... My powered driver has a torque limit. My driver bits are bought in bulk..... first and final torque are done by hand. Fun memories... Best regards, -a- Quote
cnoe Posted January 22, 2017 Report Posted January 22, 2017 I added this to my tool collection in 2016 to gain a better feel for tightening rocker cover screws. The price was low enough I hope to retain my membership in the CB club. https://www.amazon.com/Wheeler-Firearms-Accurizing-Torque-Wrench/dp/B0012AXR4S Sent from my iPad using Tapatalk Quote
RLCarter Posted January 23, 2017 Report Posted January 23, 2017 Get your A&P to Heli-Coil or Time Sert it, I believe mine has an insert in it. If your guy isn't comfortable doing it send it to the people that overhauled it. 1 Quote
Oscar Avalle Posted January 27, 2017 Author Report Posted January 27, 2017 To close the loop. Thanks for the solidarity. I still feel like an idiot, but as it was mentioned before I learned my lesson. I was able to get a used fuel selector valve. Extremely hard to find. Interestingly the most difficult part to find is not the valve itself (which is already very scare), but the cup that goes over the valve. Luckily mine I still had mine and it was in a good shape. I sent the "new valve" and the cup out to LASAR to get the valve overhauled, and the unit was sent back yesterday and it was installed today. So I am ready to go again. Now I have to find time to go flying... essential task... 7 Quote
M20F-1968 Posted January 29, 2017 Report Posted January 29, 2017 This post made me go looking for a torque screwdriver. Snap-on (and CDI which is also Snap-on) models can be found. They list for over $200 (actual retail $245) but found a new one 5-40 Ft/lbs, for $114.00. Looks like a good tool by a good maker. (CDI is the same tool made for industrial marketing). John Breda 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.