Jump to content

Inflatable door seal instructions

Wingover

By Wingover
in General Mooney Talk

 Share

Recommended Posts

Wingover Enthusiast

Wingover

Posted
Posted

Looking for help from people who installed the Bob field seal on their M20J.

I am specifically looking for help on where did you locate the little grey hose (that connects to the pump hose) that is part of the seal? Did you locate it down below the part of the door or on the side (closer to the hinge side)?

Do you need to drill a hole to route it into the door?

Any help would be greatly appreciated.

 Understand how to glue it and how to trim the plastic door cover if needed for space.

LANCECASPER Grand Master

LANCECASPER

Posted
Posted
Looking for help from people who installed the Bob field seal on their M20J.
I am specifically looking for help on where did you locate the little grey hose (that connects to the pump hose) that is part of the seal? Did you locate it down below the part of the door or on the side (closer to the hinge side)?
Do you need to drill a hole to route it into the door?
Any help would be greatly appreciated.
 Understand how to glue it and how to trim the plastic door cover if needed for space.

I did one on my previous airplane 4 years ago and ran it up under the armrest

107853b987fc53e00b65eefebd88d254.png


Sent from my iPhone using Tapatalk
Wingover Enthusiast

Wingover

Posted
  • Author
Posted
26 minutes ago, LANCECASPER said:


I did one on my previous airplane 4 years ago and ran it up under the armrest

107853b987fc53e00b65eefebd88d254.png


Sent from my iPhone using Tapatalk

Sorry, I am talking about the little grey piece tube that is part of the seal itself. It has to somehow go inside the door frame. 

LANCECASPER Grand Master

LANCECASPER

Posted
Posted
Sorry, I am talking about the little grey piece tube that is part of the seal itself. It has to somehow go inside the door frame. 

If I remember correctly I put it at the bottom and ran the black hose to it. I don’t remember if we drilled a hole or not. It wouldn’t have been a big deal to do that though.


Sent from my iPhone using Tapatalk
Wingover Enthusiast

Wingover

Posted
  • Author
Posted
14 hours ago, LANCECASPER said:


If I remember correctly I put it at the bottom and ran the black hose to it. I don’t remember if we drilled a hole or not. It wouldn’t have been a big deal to do that though.


Sent from my iPhone using Tapatalk

Thanks! Hoping others might have more information or pictures if the install (especially the grey hose)

tomgo2 Collaborator

tomgo2

Posted
Posted

Hello,

You need to drill a hole in the door as indicated in red on the attached image.  Note 5 is for Mooney aircraft models. Disregard the hole on the vertical surface. The hole on the vertical surface of the door are for non-Mooney models.

The grey valve stem of the door seal is fed through that hole to the inside of the door.

Thanks for the note @LANCECASPER

Tom

Screenshot_20241013_201442_OneDrive.jpg

Wingover Enthusiast

Wingover

Posted
  • Author
Posted (edited)
13 hours ago, tomgo2 said:

Hello,

You need to drill a hole in the door as indicated in red on the attached image.  Note 5 is for Mooney aircraft models. Disregard the hole on the vertical surface. The hole on the vertical surface of the door are for non-Mooney models.

The grey valve stem of the door seal is fed through that hole to the inside of the door.

Thanks for the note @LANCECASPER

Tom

Screenshot_20241013_201442_OneDrive.jpg

Hi @tomgo2,

Is it possible to get this (maybe PDF) by email or DM?  I am not sure if I am missing the lower right part of your picture.  I see the number 5 as 22" distance to where to drill but also see "5" at the bottom right of the picture but the rest of it is cut off.

Edited by Wingover
Name change
LANCECASPER Grand Master

LANCECASPER

Posted
Posted
1 hour ago, Wingover said:

Finished mine

IMG_2617.jpeg

Looks good.

Unless you've flown with it after the initial install to look for places that it doesn't seal quite right,  it isn't finished yet. The holder of the STC sells silicone shim material to put in places, under the seal, where it doesn't quite fit. This is especially important in that concave area at the bottom of the door. 

After a few tries when you get it to seal just right, you will notice an incredible difference when you pump it in flight. It will be worth all of the effort.

Wingover Enthusiast

Wingover

Posted
  • Author
Posted
7 hours ago, Andy95W said:

Please report on how you like it, and if you had any difficulty during installation. Thank you!

The only difficulty I had was holding the seal in place on the forward part of the door, it kept sliding off.  I managed to keep it in place after all.

Doing an oil change so won’t get a chance to fly it until next week.

  • Thanks 1
  • 4 weeks later...
Wingover Enthusiast

Wingover

Posted
  • Author
Posted
On 10/18/2024 at 12:28 AM, LANCECASPER said:

Looks good.

Unless you've flown with it after the initial install to look for places that it doesn't seal quite right,  it isn't finished yet. The holder of the STC sells silicone shim material to put in places, under the seal, where it doesn't quite fit. This is especially important in that concave area at the bottom of the door. 

After a few tries when you get it to seal just right, you will notice an incredible difference when you pump it in flight. It will be worth all of the effort.

Went on an hour flight to test the seal.  Happy to report an amazing difference in noise level, no more "hissing".  What I did during the install was to glue it in place, shut the door (go out through the baggage door) and inflate it a bit to move around between the frame of the plan and door based on the pressure of the air.  It seems that it paid off since I didn't need to realign it again.

Very happy with the product!  Thanks @tomgo2

  • Like 1
  • Thanks 1
Fly Boomer Grand Master

Fly Boomer

Posted
Posted
6 hours ago, Wingover said:

What I did during the install was to glue it in place, shut the door (go out through the baggage door) and inflate it a bit to move around between the frame of the plan and door based on the pressure of the air.

How did you move it around?

Wingover Enthusiast

Wingover

Posted
  • Author
Posted
4 hours ago, Fly Boomer said:

How did you move it around?

I didn’t. I used some tape to just hold it in place until I could quickly close the door and inflate it a bit to make sure it “moved” as in fill the gap between the airplane frame and door frame. The silicone glue that came with the kit doesn’t really hold the seal in place like superglue, you can move the seal for probably good 1/2 hour or more before the silicone cures.

  • Like 1
Slick Nick Enthusiast

Slick Nick

Posted
Posted
On 11/10/2024 at 1:49 AM, Wingover said:

Went on an hour flight to test the seal.  Happy to report an amazing difference in noise level, no more "hissing".  What I did during the install was to glue it in place, shut the door (go out through the baggage door) and inflate it a bit to move around between the frame of the plan and door based on the pressure of the air.  It seems that it paid off since I didn't need to realign it again.

Very happy with the product!  Thanks @tomgo2

Where did you purchase yours from? Does @tomgo2 sell direct? I am in Canada. 

Wingover Enthusiast

Wingover

Posted
  • Author
Posted
17 minutes ago, Andy95W said:

Hi @Wingover- when you have time, could you please take a picture of the bottom of your door?  (so I can see how you oriented the seal with regard to the slider.)

Hi Andy,

I just got back from flying so won't be at the hangar for a week.  I basically cut and rounded the slider corner (per instructions) that is closer to the seal. When I closed the door and inflated the seal to get it to dry in place it conformed to the door shape.  I will send pictures next week.

Tal

  • Thanks 1
Jetdriver Contributor

Jetdriver

Posted
Posted

We installed one on our M20F and while the installation took longer than expected the results are very worthwhile. Significant improvement in heat retention and significant decrease in ambient noise level.

Sent from my SM-S918U using Tapatalk

  • Like 1
  • Thanks 1

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
 Share
Go to topic listing
×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.