65C Wing (Damaged by falling off Jacks)) Anyone Interested?

[patriot3300]

7 hours ago, Bolter said:

If you literally cut the wings off, won't they be useless because of the continuous spar?  It would be a totally different disassembly if you want to fit the plane on a truck or in a container, AND have the wing repairable.  The popular options appear to be removing the total wing, or removing the tail, and carrying the fuselage sideways on the truck.  Either way, the wing spar is left intact.  

Thanks 

All the options have been thoroughly researched.

I am taking her apart to haul inside an enclosed trailer.

Fuselage will stay in one piece with tail unbolted.

Cheers

Stuart

[Captnmack]

There is a C in Texas with the same issue except it did not puncture the upper skin. The area it went through was an Aux fuel tank. I looked at it and I do not think you can simply do a patch. I believe it should have the entire skin section replaced. 

[patriot3300]

4 hours ago, Captnmack said:

There is a C in Texas with the same issue except it did not puncture the upper skin. The area it went through was an Aux fuel tank. I looked at it and I do not think you can simply do a patch. I believe it should have the entire skin section replaced. 

That is correct.

The  repairs needed are replacement of both wing skins.

 

[47U]

7 hours ago, Captnmack said:

The area it went through was an Aux fuel tank. I looked at it and I do not think you can simply do a patch. I believe it should have the entire skin section replaced. 

What king of damage is to the lower wing skin/bottom of the wing?

[patriot3300]

On 2/6/2025 at 6:14 PM, 47U said:

What king of damage is to the lower wing skin/bottom of the wing?

I was not able to complete the disassembly over the weekend due to horrible weather and airline delays.

I also do not wish to destroy this wing if anyone is willing to repair it.

This is the totally of the damage.

Please Pm me if you are up to the repair.

I will be going back no later than The end of March to complete the disassembly and absolutely will section the wing at that time if none are able to repair.

Cheers

Stuart

 

 

 

[47U]

6 hours ago, patriot3300 said:

I also do not wish to destroy this wing if anyone is willing to repair it.

Wow.  After seeing your last post I’m in 100% agreement with those who recommend replacing the affected wing skins.

Not sure what part of Texas you’re in… but if you’re disassembling the aircraft (either removing the tail or wing from the fuselage) for flatbed transport then that opens the potential repair locations.  Don Maxwell has rig for transport with the tail section removed.  

Mooney will manufacture the wing skins, inquire with your favorite MSC for pricing.  Hopefully, no ribs or stringers are damaged.  Your MSC will also likely have recommendation(s) on who would be a good repair facility.   

[M20E for me]

On 2/5/2025 at 7:04 PM, patriot3300 said:

Sorry to say this is the situation I expected.......

 

• 
• Supporter
• •  18
• Location: Redding CA
• Base: O85

 

Posted yesterday at 09:44 AM

Hi all, my new to me 1979 J- model (serial 0905) has an STC (SA7609SW) for Texas Composites, Inc wingtips that was installed in 1995.  Both of the lenses covering the lights are cracked, one just around the screw holes which will be manageable for some time, the other is cracked right down the middle and needs replacement.

I can't find these and believe they are likely a slightly different shape than the LASAR tips or other tips that came from factory on later J models.  They do not have recognition lights.

Anyone else out there have these wingtips and had success finding lenses?  I contacted a 3D printing company about scanning and printing new lenses, but they want $2500 just for the scan.  I might as well get new wingtips.

I tried tracking the company Texas Composites, Inc but the larger corporation that bought them out doesn't respond to me. 

Donovan 

 

 

That’s looks like mine and I bought a replacement for the right hand one from Laser.  It took a while to get it but fits fine.  Another option, if you are handy, is to make a new one.  Use your cracked on to pull a male mold off of.  The lens material is cheap and plan on several attempts to get a good one.

[Hank]

1 hour ago, M20E for me said:

That’s looks like mine and I bought a replacement for the right hand one from Laser.  It took a while to get it but fits fine.  Another option, if you are handy, is to make a new one.  Use your cracked on to pull a male mold off of.  The lens material is cheap and plan on several attempts to get a good one.

The last one I bought from LASAR, c.2017, was almost $200. Try making one, it won't hurt and is guarantees to cost you less.

[Echo]

12 hours ago, Hank said:

The last one I bought from LASAR, c.2017, was almost $200. Try making one, it won't hurt and is guarantees to cost you less.

There is the rub for me.  Such a bend over price from Laser.  Instead of taking a fair profit they rape you.  No thanks.  I will just carry on with one cracked lens thank you.

[Hank]

5 minutes ago, Echo said:

There is the rub for me.  Such a bend over price from Laser.  Instead of taking a fair profit they rape you.  No thanks.  I will just carry on with one cracked lens thank you.

I didn't have much choice, water-soaked insulation fell from the hangar ceiling onto the wingtip and knocked off the front of one.

But if it is only cracked, it should be fairly simple to make a male mold of the inside, then heat up and carefully stretch a piece of plexiglass over it. It'll take a little time, some scrap lumber and a sheet of 1/8" plexiglass from your favorite big-box store.