Parting out 67 F

[Alan Fox]

Parting out a 67 F model , plane is complete , sorry prop is already spoken for , Reg is N3463N . Engine is an IO360 19XX SFOH in 2000 .. Alan 856 419 5209

[Mooney-Shiner]

What year?

How much for the nose wheel? Is engine IO360A1A?

Edited October 28 by Mooney-Shiner

[sdmideas]

Do you have a pair (or even just one) of pitch servos? I’d take those:)

[Shadrach]

Where is it located?

[Alan Fox]

Located at KVAY (East coast) AP is a century 2000 ,  Nose wheels are 500 , I have a few .. Engine is a IO-360 A1A wide deck , 19XX Hours since factory overhaul in 2000 , Last flown 2022

[N204TA]

For what it’s worth, you have a 1968 M20F built and certified in 1967.
 

My ‘68 F was born N3460N, S/N 680059.  Coincidentally, I saw the F between ours, N3461N, S/N 680060, in Kerrville last month.  Small world.

[BillyT0020]

What do you want for the engine? I’m looking for a project to rebuild over time. 
 

Billy 

[N177MC]

Looking for a 540016-507 Mooney M20K Nose Gear Retract Truss Assembly 

[Alan Fox]

Engine is 17800.00

[ProtoFly]

Do you have:

Passenger side windshield interior trim piece
Back seat recline levers

[Alan Fox]

5 hours ago, ProtoFly said:

Do you have:

Passenger side windshield interior trim piece
Back seat recline levers

Levers will go with seats

[Mooneydreamr]

I would be interested in a heated pitot tube.

[ProtoFly]

On 11/4/2024 at 10:25 PM, Alan Fox said:

Levers will go with seats

To clarify:  Looking for right windshield moulding, 130099-003 (I think - see pic).

And the levers are the ones on the rear side panels that pull cable to release the rear seat backs for adjustment.

[Alan Fox]

On 11/6/2024 at 6:24 AM, Mooneydreamr said:

I would be interested in a heated pitot tube.

I have a heated pitot 12 volt and tested 800.00

[Mooneydreamr]

Alan, I would be interested in seeing a picture and doing a transaction. Let me know the next steps. Probably better to reach me at my email address or phone number: briscokevini@yahoo.com  (901) 652-0028

[podair]

Do you have the landing gear motor and actuators? 20:1 or 40:1 ?

[Shadrach]

Ram air cable?

[DCarlton]

Flap / Trim Indicator Plate ? 

[DCarlton]

If it's in really good shape, the U shaped sheet metal piece that bridges the gap between the lower fuselage and tail?  

[Alan Fox]

On 10/31/2024 at 3:58 AM, N177MC said:

Looking for a 540016-507 Mooney M20K Nose Gear Retract Truss Assembly 

I have one off of a 252 , and a 83 J should be the same. 1000.00

[Alan Fox]

On 11/8/2024 at 5:28 PM, Mooneydreamr said:

Alan, I would be interested in seeing a picture and doing a transaction. Let me know the next steps. Probably better to reach me at my email address or phone number: briscokevini@yahoo.com  (901) 652-0028

 

[Mobius708]

Do you still have a pilot side interior wall trim? If so, what color? I could also use the plastic trim around the trim/flap indicator and air vent.


Sent from my iPad using Tapatalk

[MoonFlyer68]

I didn't see it mentioned anywhere, is this a J-bar airplane?  If so, what is the condition of the downlock block?  Also I may be interested is the interior piece for the baggage door.  Mine is getting in rough shape.  Thanks

[Alan Fox]

On 11/25/2024 at 6:00 AM, MoonFlyer68 said:

I didn't see it mentioned anywhere, is this a J-bar airplane?  If so, what is the condition of the downlock block?  Also I may be interested is the interior piece for the baggage door.  Mine is getting in rough shape.  Thanks

I have one of the Dave Staffelt "new" downlocks in stock , I have resisted selling it because it is an OPP part... 

[Sabremech]

11 hours ago, Alan Fox said:

I have one of the Dave Staffelt "new" downlocks in stock , I have resisted selling it because it is an OPP part... 

Those downlock are perfectly legal!