rockydoc Posted October 21, 2014 Report Posted October 21, 2014 Over the last six months or so, I have had five different avionics tech trying unsuccessfully to solve this problem. My intercom volume is very low. My radio volume decreases above 3500' and my radio static increases above 3500' to the point that I can't communicate with ATC. Above 7000' communication is totally impossible. We have tried cleaning and tightening the antennae connections and even tried switching antennae locations. Nothing seems to work. Ideas? Rocky Quote
1964-M20E Posted October 21, 2014 Report Posted October 21, 2014 I’ve had some serious static in certain areas around New Orleans on specific frequencies 119.9 KNEW TWR and 119.5 KMSY TWR and this was down low. This was on both radios and it happens around an antenna farm and near downtown. We ended up deciding it was the ELT 121.5mhz causing the interference. I do not know why it would but it does. Unplug the ELT antenna and it goes away. Quote
ArtVandelay Posted October 21, 2014 Report Posted October 21, 2014 Same problem with both radios? Static listening or transmitting or both? I assume you try to increase the volume using both radio control as well as your audio panel? Same with copilot side? Did you try switching magneto off to see if it makes a difference? Quote
Skywarrior Posted October 21, 2014 Report Posted October 21, 2014 I'm not an electronics expert, and I didn't stay at a Holiday Inn Express last night... but it sounds like a 'box' somewhere depends upon being hermetically sealed - but isn't. 1 Quote
FloridaMan Posted October 21, 2014 Report Posted October 21, 2014 I'm with skywarrior on this. Have you removed and reracked your radios? Quote
mooniac15u Posted October 21, 2014 Report Posted October 21, 2014 Over the last six months or so, I have had five different avionics tech trying unsuccessfully to solve this problem. My intercom volume is very low. My radio volume decreases above 3500' and my radio static increases above 3500' to the point that I can't communicate with ATC. Above 7000' communication is totally impossible. We have tried cleaning and tightening the antennae connections and even tried switching antennae locations. Nothing seems to work. Ideas? Rocky Most intercoms should be wired so that turning off the intercom connects the pilot headset directly to comm 1. If you turn off the intercom is the problem still present? That might help you determine if the problem is the radio or the intercom. Quote
rockydoc Posted October 21, 2014 Author Report Posted October 21, 2014 Most intercoms should be wired so that turning off the intercom connects the pilot headset directly to comm 1. If you turn off the intercom is the problem still present? That might help you determine if the problem is the radio or the intercom. Good point. I'll try turning off the intercom and see if it makes a difference. I have pulled both radios out of their rack and re-inserted them. Didn't make any difference. Quote
Mooneymite Posted October 21, 2014 Report Posted October 21, 2014 Your radios are hypoxic. Try some oxygen. 1 Quote
carusoam Posted October 21, 2014 Report Posted October 21, 2014 Hmmm. O2 effects on hearing....? Mooneymite could be onto something...! Best regards, -a- Quote
Piloto Posted October 22, 2014 Report Posted October 22, 2014 This could be a cooling problem. As you go higher in altitude the air density is less, thus the cooling efficiency of avionics decrease. Check the avionics fan and ducting. You may have an electronic component that has gone marginal with temp. Aim the side cabin vents toward the avionics stack to improve cooling. José Quote
rockydoc Posted October 22, 2014 Author Report Posted October 22, 2014 This could be a cooling problem. As you go higher in altitude the air density is less, thus the cooling efficiency of avionics decrease. Check the avionics fan and ducting. You may have an electronic component that has gone marginal with temp. Aim the side cabin vents toward the avionics stack to improve cooling. José Buen punto José. Gracias. Muy amable. Rocky Quote
N601RX Posted October 22, 2014 Report Posted October 22, 2014 Your plane probably doesn't have a cooling fan, unless someone has added one. The older ones came from the factory with a cooling louver behind the radio stack hooked up to a ram air vent to the outside. Not a good idea for cooling modern stuff. I was having cooling issues in the center of the stack (KNS80). We removed the ram air and cooling vent and added a fan with a tube the the rear of each piece of equipment. I haven't had any problems since. Quote
rockydoc Posted October 22, 2014 Author Report Posted October 22, 2014 Your plane probably doesn't have a cooling fan, unless someone has added one. The older ones came from the factory with a cooling louver behind the radio stack hooked up to a ram air vent to the outside. Not a good idea for cooling modern stuff. I was having cooling issues in the center of the stack (KNS80). We removed the ram air and cooling vent and added a fan with a tube the the rear of each piece of equipment. I haven't had any problems since. That sounds like a great solution whether its responsible for my existing problem or not. You don't happen to have a photo of the cooling fan and tubes as well as a source for the fan. It sounds like a special fan that I would like to buy. Quote
N601RX Posted October 22, 2014 Report Posted October 22, 2014 I used this one. I didn't have enough room for anything larger. https://www.aircraftspruce.com/catalog/avpages/cyclone21.php Quote
rockydoc Posted October 22, 2014 Author Report Posted October 22, 2014 I used this one. I didn't have enough room for anything larger. https://www.aircraftspruce.com/catalog/avpages/cyclone21.php That looks perfect. Where on the trays and how did you connect the other end of the tubing to the trays? Thanks for the help. Rocky Quote
N601RX Posted October 22, 2014 Report Posted October 22, 2014 If avionics need external cooling the Manufacturer puts a round inlet on the back of the tray to slide the flex tube from the fan over. Quote
rockydoc Posted October 22, 2014 Author Report Posted October 22, 2014 If avionics need external cooling the Manufacturer puts a round inlet on the back of the tray to slide the flex tube from the fan over. Thanks again. Rocky Quote
takair Posted October 22, 2014 Report Posted October 22, 2014 What type of radios, intercom and audio panel do you have? Quote
rockydoc Posted October 22, 2014 Author Report Posted October 22, 2014 What type of radios, intercom and audio panel do you have? King KX-155 and TKM MK-11 radios with KA-134 audio panel and Sigtronics SPA-400 intercom Quote
takair Posted October 23, 2014 Report Posted October 23, 2014 Pretty bulletproof setup. As I recall, those don't have cooling ports. Suggestion above, to turn off intercom, is a good one. This is a long shot, have you tried different headsets? You may have a ground problem too, don't know how it relates to altitude, but that could be common to all. Do you have a voltmeter, is it possible your alternator or generator is not charging at altitiude? Things tend to arc with thin air, this bad brushes can be worse. A friend recently had a loose lug on the alternator, similar story. Quote
rockydoc Posted October 23, 2014 Author Report Posted October 23, 2014 Pretty bulletproof setup. As I recall, those don't have cooling ports. Suggestion above, to turn off intercom, is a good one. This is a long shot, have you tried different headsets? You may have a ground problem too, don't know how it relates to altitude, but that could be common to all. Do you have a voltmeter, is it possible your alternator or generator is not charging at altitiude? Things tend to arc with thin air, this bad brushes can be worse. A friend recently had a loose lug on the alternator, similar story. The KX-155 does have a cooling port. I'm not certain about the others, but I ordered the recommended avionics cooling fan with 3 air outlets so I plan on aiming a hose at any tray that doesn't have a cooling port. I have tried various headsets--no difference. I have a voltmeter and constantly check my generator output--which is consistently good. I think your comment about a good ground needs pursuing. I think I'll run an individual ground wire directly to each radio tray or should I connect it to each radio chasis inside of the tray? Is the Mooney frame under the instrument panel a suitable grounding site? Rocky Quote
takair Posted October 23, 2014 Report Posted October 23, 2014 The problem is that the chassis ground and audio ground within the radio is different. The audio grounds coming from the connector are typically grouped together such that the audio panel, intercom and radios audio circuits have a common connection point to airframe ground. While this will ohm out the same as chassis, it does make a difference in performance. (Noise, volume, quality) In addition, ideally the headset plugs are isolated and the ground is run back to audio ground. The tube chassis is a good ground. The sheet metal panel is screwed to this. It it possible that the radio/audio ground is connected to the sheet metal, but the sheetmetal panel is not well connected to the tube. Check to see if your panels are well grounded. Not sure how a B panel is secured. Frequently people will use the screw that holds the panel to the lower tubing to ground, and these will get loose and cause problems. Still unsure how the altitude would make this worse....so it may be a long shot. 1 Quote
rockydoc Posted October 23, 2014 Author Report Posted October 23, 2014 The problem is that the chassis ground and audio ground within the radio is different. The audio grounds coming from the connector are typically grouped together such that the audio panel, intercom and radios audio circuits have a common connection point to airframe ground. While this will ohm out the same as chassis, it does make a difference in performance. (Noise, volume, quality) In addition, ideally the headset plugs are isolated and the ground is run back to audio ground. The tube chassis is a good ground. The sheet metal panel is screwed to this. It it possible that the radio/audio ground is connected to the sheet metal, but the sheetmetal panel is not well connected to the tube. Check to see if your panels are well grounded. Not sure how a B panel is secured. Frequently people will use the screw that holds the panel to the lower tubing to ground, and these will get loose and cause problems. Still unsure how the altitude would make this worse....so it may be a long shot. Well, verifying the existence of a good audio ground and headset plugs ground is a good starting point for me to troubleshoot. Thanks for the detailed input. Rocky Quote
N601RX Posted October 23, 2014 Report Posted October 23, 2014 If its strictly a cooling problem, I would think that you should notice it getting better or at least happening at a higher altitude now that the weather has cooled down. If it is altitude related it may be an alternator arcing like Rob mentioned or a mag starting to misfire. I think I would take it up to an altitude that causes the problem and try turning pulling the alternator main and field breaker. If that doesn't help then I would try each mag separately or possibly even both mags. That will rule out 3 things that will be difficult to rule out on the ground. 1 Quote
Bill Dunn Posted October 23, 2014 Report Posted October 23, 2014 those SPA 400s are known to have issues. we have replaced tons of them here at the shop and we had about 20 laying in a cabinet that were all broken. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.