All Activity

This is wonderful to hear, and I am still hugely excited about this path for my 68C. It's my forever plane, and I have squeezed extra speed out of it by various means, making it a solid 150kt cruiser. I flew out to KOSH this year in loose formation with some Bonanza driver friends, who have been ribbing me ever since for having to slow down by 10kt on my behalf. I'm pretty sure this mod will be cheaper and healthier way of medicating my hurt feelings than drugs, or buying an A36

Andre, if the prop is a search for speed, the issue may be that your plane is post 1968 "clean wing" Mooney production and is consisered a "dirty wing" due to non flush rivets done by Butler and Republic in a cost savings venture. Per Coy Jacobs in his book backward tails The later Butler and Republic aircraft with dirty wings can be several knots slower than earlier flush rivet retractable step clean wing Mooney aircraft. This speed deficit can easily be remediated with cowl, windshield and other 201 type mods per Jacobs.

That thread is for the Safe Flight lift detectors that were used in older Mooneys. They are a proprietary design and are very expensive to replace, so I can see the appeal. The OP’s Mooney uses a Mooney lift detector assembly that incorporates a generic switch, though, of a completely different design that at least just a couple years ago was cheaply replaceable. It sounds like his problem lies elsewhere, though, regardless.

At 6500' and above at 2500 rpm and 9-10gph I don't make 24"mp so NOT a problem for me. I am reducing MP on decent so NOT above 24"mp. In climb I am max rpm so again, outside of 24". If down low say 3000' on a short hop I just set mp at 23.

Thanks @Rick Junkin. I too suspect a connection issue. Looking back through the EDM data collected during the past year, this problem has been intermittent, but increasing if frequency and severity of late. The transducers included with my JPI use MetriPak connectors, which are "supposed" to be weather resistant. I'll go ahead and remove the cowl and give them a look see.

It will be important to clearly describe your engine for this, but it might be nice (and informative) to have a specific thread on power settings we all use and why. Obviously there’s going to be a lot of differences based on the different TSIO-360 models and aftermarket intercoolers or wastegates. I actually think there’s quite a wide variety of different ways we each look at this, even though my POH shows only 10 knots (and ~1.4gph) between 65% and 75% power which is noted as max recommended. Ive been happily flying my 252 (SB engine) at 65% LOP for about 6 months, but I want to be aware of what else I might try and why? @shawnd mentioned that he only flies ROP just to keep his CHTs high enough in the winter. I hadn’t thought of that. So last week I decided to try some settings out of the POH, except I’m not a fan of “peak TIT” , so I thought I’d add 1gph to them as a start to make sure I was really ROP. I was cruising along at 15,500’, 65% LOP and decreased mp to 28, increased rpm to 2500 and mixture up to 13.7. Should be 75% except 1gph richer than peak. Well my speed increased a little, but my CHTs started up and I gave up at 396f (and rising) on #3. Maybe I needed more ff to be richer? Dunno. But it should have been at least as good as the POH setting of 12.7gph with the same rpm/mp, no? So for now, here’s what I like with my MBcSB engine (220hp)… 2350rpm, 29.5mp, 10.4gph. That gives me about 20f LOP. It’s smooth, efficient, and book speed or slightly better than 65% “peak tit” in the poh. I have also run 2350, 30.5, 11.2gph for 70%lop and it’s fine but only gains maybe 3 knots. The 65% setting has my CHTs between 315-350f at 15,500’ and -2C OAT which seems good to me. So what do others do? If you run ROP, how far rich are you from the poh? Why do you run rop? Maybe it doesn’t run smooth LOP? Anyone use the poh numbers (PO of mine used POH 70% numbers a lot).

Subtitle: The overhaul from hell... Just got my M20J back from overhaul. Mind you this was after two test flights. The first flight, oil leaking from governor, we pulled it and overhauled it. Put it back on, second test flight was leaking from gasket. Replaced that gasket, third time was the charm and no leaks and I brought the Mooney back home. Next weekend, I flew it about 8 hours, to and from Omaha and Oklahoma - performed great with no issues on the flight. After landing, taxi back, and shutdown was uneventful. Skip forward a week and I go fly again. Engine start, taxi, runup was uneventful. Mag check was good. On takeoff roll engine sounded weird and like it wasn't making full power. I look down and see ~2200-2300 RPM. I abort the takeoff. A Couple of more static runs and it seems to be governed just above 2000 RPM. I pull the cowl, check the cable and it seems to be making it to the low RPM stop just fine. I was sure it was the governor since it was having issues. I have the governor removed and sent to the place that did the overhaul. They said it bench tested good... Has anyone seen anything like this before? Looks like I'm pulling the prop to send it to the shop to see if there's something wrong with the prop. It seems that with enough RPM there is something leaking into the prop hub to increase the oil pressure to increase the pitch on the blades. Attached videos show the runup. When I took this video, it looks like #2 cylinder dropped off (not sure if that was due to over boosting it or something else) but fuel flow and manifold pressure all looked good. #2 seems to keep good ignition the rest of the runs. I didn't want to run it too much over square. I also haven't checked the accuracy of the tachometer but it seems to be sounding like the prop is digging in and causing rough running.

I've got a Starlink Mini. I've used it in flight. My opinion.... Meh. Not worth it for me as a pilot. If you are wanting to provide in-flight entertainment for passengers, it's amazing. For thunderstorm dodging weather info? Are you freaking crazy? Do you really want to explain to the NTSB and FAA that's what your plan was after you've had an in-flight emergency or incident or accident? Filing flight plans? Either do it on the ground or talk on the radio to ATC. If you are filing a flight plan that means you are VMC, so you need to be looking outside for other traffic. This sounds like a a bad idea that some marketing shill that isn't a pilot might put in an advertisement, like "Creating your grocery list on the laptop while you drive to the grocery store." If you are just looking for personal entertainment and staying in communication with people in flight but you are just ashamed to say that's what you want it for, well... I don't know what to tell you. Long XCs with an autopilot are kind of boring. Listen to music that is already downloaded or an audiobook or a podcast or whatever.

Just re-read (skimmed). Mooney began selling the 252 in 1986. May 1, a 252 set a non-stop record from Los Angeles to New York in 8:20. Previous record was held by a Bonanza in 11:56. Think about that: 3:36 faster than the best Bonanza. EDIT: Apparently, the 252 record still stands:

Thanks, I will forward to A&P to verify as the left magneto is a Surefly to make sure it can/was adjusted properly.

Congratulations! You now own one of the finest traveling airplanes in general aviation. It is a high performance aircraft and it won’t tolerate low performance pilots well. You now have the ability to fly in the flight levels and travel long distances quickly while burning relatively little gas. Keep in mind that high performance turbocharged engine can be roasted in a couple of minutes if you aren’t paying attention. Personally, I wouldn’t want to fly a turbocharged engine without a good engine monitor. Three things I recommend - 1. Get plenty of Mooney specific training before you fly your plane…and especially get good instruction on how to properly use oxygen cannulas before flying on oxygen above 12,500’. 2. Get instrument rated as soon as possible. 3. Put the gear down before you land.

When you changed the timing, did you change the left magneto to one with a reduced lag angle. If not, it will be firing late during start. Here is the Lycoming SI. It's no longer on Lycoming's website (Lycoming only posts the most commonly requested service literature) but is still available from Lycoming if you ask tech support. SI 1325 Timing Change for IO-360 Series Engines.pdf

Awesome!

I did it on the pressure transducer for a Saratoga landing gear. The connector was intermittent and unobtainable. Worked great afterward. They weren’t AMP CPC connectors.

Only 13 more to go Pinecone! Impressive Thanks for the link!

Here it is! I had to try a couple scanners because of the holes for the spiral bound pages and I cleaned up the final scan a bit. Let me know if you find any issues. I already uploaded it to the files section as well, just waiting for approval. The Backwards Tales Rev 8 - Coy G Jacob.pdf

I don't think I've ever seen somebody suggest replacing a pinned connector with handshake terminals before.

@0TreeLemur Found it BENZ AIRBORNE-KULITE TRANSDUCER.pdf

I take a different view of the failure mode of these switches. The switches have internal mechanisms that rock a contact arm between two stable positions. I think the predominant failure mode is the mechanism getting hung up because any lubrication added at the factory has dried up years ago and because of dirt getting inside and mucking up the works. They are in a bad place with regard to getting stuff blown in. Spraying lube in doesn’t help the contacts, it loosens up the mechanism. These switches are sealed, but the seals don’t last forever. They are rubber and it gets hard and looses its compliance after years in the elements. lubing the switch, will probably give it a few years before it needs more service, but the best plan is to replace the switch. They are somewhat hard to come by.

RadarScope looks like a great app, and for $10/year, cheap too.

Check the barrel connector on the transducer pigtail. It’s likely dirty/corroded. Cleaning it up may provide a short term fix. It worked on my Bravo. There’s a service instruction from the transducer manufacturer that essentially says to replace the barrel connector with individual knife connectors on each wire. I have it filed, once I get to my computer I’ll send you a copy.

Did this to mine last year. He also shampooed the interior. Looks great!

You missed out. On several of the topic pages there were dozens if not hundreds of messages supposedly giving you the phone number to call to change your airline ticket or something like that. They are trying to get all of the various AI summaries to redirect people to their scam phone number instead of the real one. Example article about this sort of thing: https://www.zdnet.com/article/scammers-are-sneaking-into-googles-ai-summaries-to-steal-from-you-how-to-spot-them/

Just wait until your 12-months expires. I always renewed when the ads appeared, but the new system let me sign up for auto-renewal so I won't see them for several years.

Well, if the definition of ceramic is, as listed in your link, "an inorganic, non-metallic", that excludes lots of polymers, since they are organic. Seems more like marketing buzzword hype.