Trim Boot Alternatives

[AerostarDriver]

My effort to locate a trim duct/boot for an E model has come up with nothing, only to be told they are on backorder indefinitely. Has anyone come up with an alternative like scat hose?

[Ragsf15e]

  On 10/24/2022 at 7:53 PM, AerostarDriver said:

My effort to locate a trim duct/boot for an E model has come up with nothing, only to be told they are on backorder indefinitely. Has anyone come up with an alternative like scat hose?

Expand  

Are you looking for the intake duct?  Those do seem difficult to find.  Is it repairable?

If it’s a different part, throw up the part number and maybe check the used/serviceable stuff…

[AerostarDriver]

This is the boot that goes over the trim jack screw.
914081-003

[Utah20Gflyer]

  On 10/24/2022 at 8:33 PM, AerostarDriver said:

This is the boot that goes over the trim jack screw.
914081-003

Expand  

That part number seems to be a bushing.  I don’t remember any kind of boot covering my trim jack screw. 
 

Just to verify, are you taking about the jack screw in the tail of the plane that causes the tail to pivot?

[N201MKTurbo]

I think he is talking about the boot that covers the jack screw and link in the tail. It lives between the fuselage and the tail.

Not that I'm advocating using non-approved parts, but a piece of corrugated radiator hose would keep the dirt out.

[Guest]

  On 10/24/2022 at 8:33 PM, AerostarDriver said:

This is the boot that goes over the trim jack screw.
914081-003

Expand  

Look for an email from my wife tomorrow.

 

[cliffy]

Look at 1  1/2" SCAT tubing    Single wall

Of course you have to disconnect the jack screw to get it on

Edited October 25, 2022 by cliffy
add

[AerostarDriver]

  On 10/24/2022 at 9:50 PM, Utah20Gflyer said:

That part number seems to be a bushing.  I don’t remember any kind of boot covering my trim jack screw. 
 

Just to verify, are you taking about the jack screw in the tail of the plane that causes the tail to pivot?

Expand  

 

  On 10/24/2022 at 11:32 PM, N201MKTurbo said:

I think he is talking about the boot that covers the jack screw and link in the tail. It lives between the fuselage and the tail.

Not that I'm advocating using non-approved parts, but a piece of corrugated radiator hose would keep the dirt out.

Expand  

 

  On 10/25/2022 at 12:12 AM, M20Doc said:

Look for an email from my wife tomorrow.

 

Expand  

Presently living in a sea of part numbers and copied the wrong one:

740156-003

False alarm on the bushing, Clarence already helped me track those down.

[AerostarDriver]

  On 10/25/2022 at 12:40 AM, cliffy said:

Look at 1  1/2" SCAT tubing    Single wall

Of course you have to disconnect the jack screw to get it on

Expand  

Not presently a problem.

 

[Ragsf15e]

  On 10/25/2022 at 7:59 PM, AerostarDriver said:

Not presently a problem.

 

Expand  

Yikes.

[AerostarDriver]

  On 10/25/2022 at 8:48 PM, Ragsf15e said:

Yikes.

Expand  

All I am going to say at this point is that I have learned a lot. Additionally, if you're interested in making your Mooney(or radial powered airplane) perfect, I highly recommend Mike at Round Power Aviation in Orange, Ma.

Edited October 26, 2022 by AerostarDriver

[cliffy]

Just as a reminder - the 2    1/4 inch bolts that hold the tail on are close tolerance bolts.

Regular AN bolts will not work as they allow too much play in the bolt bushings. The movement tolerances are very small Check the MM

Also many do not realize that the hinge is actually a secondary load path for the entire tail assembly 

[Jpravi8tor]

Can you please post some close-ups of the tail assembly? its always nice to have reference photos 

[GA_Mech]

I’m also having difficulty finding the part 740087-003 trim duct. I took off a spring with canvas sewn onto it but the canvas was deteriorated. Not finding the actual part… 

[Kelpro999]

  On 2/15/2023 at 5:55 PM, GA_Mech said:

I’m also having difficulty finding the part 740087-003 trim duct. I took off a spring with canvas sewn onto it but the canvas was deteriorated. Not finding the actual part… 

Expand  

I looked for the same part only to find a piece of scat is the replacement 

[47U]

  On 2/15/2023 at 5:55 PM, GA_Mech said:

I’m also having difficulty finding the part 740087-003 trim duct. I took off a spring with canvas sewn onto it but the canvas was deteriorated. Not finding the actual part… 

Expand  

It would seem a light-weight canvas fabric could be patterned and sewn up to fit the ‘wire spring’ and replace the original material.  Sew velcro on the seam and it could be easily removed for the 100 hr/annual inspection.

I wonder though, if the jackscrew is even exposed to that much dirt.  It’s enclosed pretty well with the panels.  Unless you’re operating frequently on unimproved runways (aka, piperpainter), is the jackscrew boot even necessary?  

Maybe we should have a poll…

[Skates97]

  On 2/15/2023 at 10:49 PM, Kelpro999 said:

I looked for the same part only to find a piece of scat is the replacement 

Expand  

 

  On 2/15/2023 at 11:21 PM, 47U said:

It would seem a light-weight canvas fabric could be patterned and sewn up to fit the ‘wire spring’ and replace the original material.  Sew velcro on the seam and it could be easily removed for the 100 hr/annual inspection.

I wonder though, if the jackscrew is even exposed to that much dirt.  It’s enclosed pretty well with the panels.  Unless you’re operating frequently on unimproved runways (aka, piperpainter), is the jackscrew boot even necessary?  

Maybe we should have a poll…

Expand  

Mine had nothing there when I bought it. When the bolts/bushings/bracket were replaced three years ago because my AP/IA felt there was too much play I ordered the replacement boot from Lasar. They sent a piece of scat tube that was a few inches long. 

[GA_Mech]

This was my solution… found a rubber bellows and trimmed to fit.

[hammdo]

Clever!

-Don

[Lionudakis]

Perfect ! Any help to what size or where you sourced your from? It looks like a sutiable replacement for a part not available 

[CMMPilot]

I just serviced my trim jack screw assembly and the original boot was full of gunk/dirt/grease and when I tried to clean it it started shredding. Obviously I jumped onto MS to see what others had done. The scat hose was a great idea, so I grabbed some 2 1/2” hose, cut a 4 1/2” piece, and cut about one ring of wire from each end. Bent the end of the wire and covered it (and the string ends) with a little RTV. 
I bent the first wire ring on one end into a square so it would rest on the mounting tabs and make it easier to screw on. The other end floats so I squeezed it into an oval so it fit over the bolt better on the tail side.  
I think it turned out much better than factory. Here are some photos. 
Chris