jsimmons619 Posted April 28, 2020 Report Posted April 28, 2020 Has anyone replaced the windlace (see picture 1) for the entry doorway on their M20J? I'm looking to tackle this project myself but see some obstacles. How do you removed the handle attached to the front fuselage door frame used for entry assistance (see picture 2). How is the windlace attached to the frame (screws or rivets)? I welcome your feedback and suggestions. Quote
carusoam Posted April 28, 2020 Report Posted April 28, 2020 Yes... easy first new 2U project... I bought the windlace from the same place I bough the carpet and side panels... Use the original to help with the planning and measuring of holes... getting screws back in their original locations can be challenging. But better than drilling a lot of extra holes... Everybody that sits right seat... appreciates the look of new windlace... They are really un-nerved by a ragged one dangling near their eyeballs... PP thoughts on, not a mechanic.. Best regards, -a- Quote
PTK Posted April 28, 2020 Report Posted April 28, 2020 48 minutes ago, jsimmons619 said: Has anyone replaced the windlace (see picture 1) for the entry doorway on their M20J? I'm looking to tackle this project myself but see some obstacles. How do you removed the handle attached to the front fuselage door frame used for entry assistance (see picture 2). How is the windlace attached to the frame (screws or rivets)? I welcome your feedback and suggestions. This was not very simple in my case! I had the same question and after some research I discovered mine are indeed rivets! Yours look like mine do. I also have them around the baggage door wind-lace. It was too many to drill out so I didn’t bother. My wind-lace is in good condition and it didn’t warrant all that work. I wanted to change out to leather. Maybe one day! But not as simple as removing some screws. Quote
carusoam Posted April 28, 2020 Report Posted April 28, 2020 That’s the structural windlace, Peter! -a- Quote
jsimmons619 Posted April 28, 2020 Author Report Posted April 28, 2020 Hi carusoam, How did you remove the grab handle? I cannot seem to find how to remove the cover over the mounting screws or bolts. Thanks for your response. Quote
PTK Posted April 28, 2020 Report Posted April 28, 2020 On 4/28/2020 at 3:48 PM, carusoam said: That’s the structural windlace, Peter! -a- I don’t think so Anthony! I’m specifically referring to the cord wind-lace around the cabin and baggage doors. In my 201 it is secured down under that shiny aluminum piece which is riveted. At least around the baggage door. Quote
PT20J Posted April 28, 2020 Report Posted April 28, 2020 2 hours ago, jsimmons619 said: Hi carusoam, How did you remove the grab handle? I cannot seem to find how to remove the cover over the mounting screws or bolts. Thanks for your response. I’m going to take mine apart next month and I’d like to know also. From the IPC it appears the are just stuck on with double sided tape, but it’s not all that clear. Skip Quote
cliffy Posted April 28, 2020 Report Posted April 28, 2020 In my D model they used contact cement and short screws, Gotta take the inside panels off to get to it. Quote
carusoam Posted April 28, 2020 Report Posted April 28, 2020 Gents, unfortunately, my experience came from my 65C... The 65C had a grab handle for the door... two simple bolts, one at each end of the handle... The sheet metal screws for the windlace were just hidden behind the plastic wall panels... Double check which direction the material goes... hiding it under metal and rivets doesn’t sound like a Mooney method for something like that... As far has the fancy plastic covers over the bolts go... they appear to be snap in place... Good luck with your project... PP thoughts only, not a mechanic... Best regards, -a- Quote
kortopates Posted April 28, 2020 Report Posted April 28, 2020 Like @cliffy says above, you'll need to open it up at least partially to verify. My door windlace was secured with small screws only into aluminum. That made it really easy when I did mine years ago when I put in leather windlace to match my nice new AeroComfort seats. If its attached by the pop rivets like Peter's above and as I sort of remember my baggage door was, then its a bigger job of course. I can't recall much detail other than it wasn't hard but slow detailed work, one screw at a time just like Anthony describes. No glue was on mine anywhere. 1 Quote
jsimmons619 Posted April 29, 2020 Author Report Posted April 29, 2020 Hi PTK, carusoam, PT20J, cliffy and kortopates, Thanks for sharing your thoughts on the windlace replacement. I'm currently awaiting the replacement windlace material. Once that arrives I plan to tackle the project. I have made some minor efforts at removing the handle but still haven't determined how those apparent covers over the handle fasteners are attached. I'd hate to damage the covers and create a new problem. Once I solve that issue, I'll post the solution for others who may face the same covers. 1 Quote
carusoam Posted April 29, 2020 Report Posted April 29, 2020 Each cut location, and depth, will help shape the windlace just like the original... Expect Peter’s advice to be spot on... he went to the next level, or several levels up, with leather wrapped yokes and really nice seats... I struggled with the windlace... PP thoughts only, not a mechanic... Best regards, -a- Quote
jsimmons619 Posted April 29, 2020 Author Report Posted April 29, 2020 Hi All, FYI. I discovered that the center section of the handle cover was removable. Super tight fit and hard to visualize at first. One more hurdle down for the project. Jim 2 1 Quote
carusoam Posted April 30, 2020 Report Posted April 30, 2020 Great follow-up Js! Any headway on finding out how the windlace is held in place? Best regards, -a- Quote
jsimmons619 Posted May 1, 2020 Author Report Posted May 1, 2020 I have not gone further in the disassembly yet. I have not received the new windlace material yet. I'll advise once I proceed further. 1 Quote
Oldguy Posted May 1, 2020 Report Posted May 1, 2020 On my '84 J the windlace is held in by little, tiny Phillips-head screws. Some of them are under the plastic interior parts, so when I was redoing the plastic in my plane, it was a good time to replace the windlace. Two things I learned from doing it: Save the existing windlace and use it for a pattern for the holes where the screws/rivets go. It also helps to know where you need to cut into the material to go around corners. Patience. It may have taken 10-15 minutes to get a single screw in for the first few I did. It finally sped up as I became more adept at not slicing my hands on sharp aluminum, but it was never a job I would commit to having done in a specified amount of time. Stubby screw drivers are too large. I ended up with some jewelers screw drivers that worked fairly well. And a large box of band-aids. 1 Quote
jsimmons619 Posted May 1, 2020 Author Report Posted May 1, 2020 Thanks for sharing your thoughts. I have received enough windlace material to tackle the cargo door (more on backorder). I found that my '87J has the same tiny phillips head screws. At times it appeared that rivets would have to be drilled but that was not necessary. Right now I have the old one removed and will be installing the new on later today. 1 Quote
carusoam Posted May 2, 2020 Report Posted May 2, 2020 The cuts in the mounting material... Location and depth... are important for how the material bends and lays flat around the curves of the doors.... Essentially the cuts match the bends... copying the old one is the easiest way to get it right... Stuff I learned on my M20C... Best regards, -a- 1 Quote
bradp Posted May 2, 2020 Report Posted May 2, 2020 Courtney (wife) did it for me. Bought some windlace from the auto upholstery supply shop and the tab just fits in behind the aluminum trim. Not too difficult. Good results. Quote
carusoam Posted May 3, 2020 Report Posted May 3, 2020 On 5/1/2020 at 9:54 PM, bradp said: Courtney (wife) did it for me. Bought some windlace from the auto upholstery supply shop and the tab just fits in behind the aluminum trim. Not too difficult. Good results. Did I mention that a family that does maintenance together.... This is a really good sign! -a- Quote
jsimmons619 Posted May 15, 2020 Author Report Posted May 15, 2020 Old windlace replaced. Actually was a big job and took days but the end result is well worth the effort. Pictures of before and after . 2 Quote
PT20J Posted May 30, 2020 Report Posted May 30, 2020 I've spent a couple of days removing the weather stripping and most of the windlace from my 1994 M20J. I used half a quart can of 3M General Purpose Adhesive Remover to clean up the glue from the weather strip. For the baggage compartment, the left side of the windlace is attached with countersunk pop rivets that have to be drilled out. The top and right side are held on with #4 flat head sheet metal screws. All the main door windlace is held on with the same screws. The biggest pain is the section behind the circuit breaker panel. I'm going to have to spend some time getting the panel out of the way to access the screws. I got some nice windlace from Bruce Jaeger -- he's shipping during the pandemic. I'm replacing the door seals with T-9088 from Brown Aircraft Supply which is called out in the IPC. That appears to be what was on the main door. The baggage door had a similar material but a foam core rather than a hollow core as the T-9088. Both were squashed flat. Skip Quote
jsimmons619 Posted May 31, 2020 Author Report Posted May 31, 2020 Agreed that CB panel was the toughest area to work on. Congratulations upon completing the job. It makes a much better first impression around the entry door. Quote
trevttu76 Posted December 5, 2022 Report Posted December 5, 2022 I am struggling with the circuit breaker avionics panel portion on my 78 J model. What is the process there? I was contemplating cutting it out and abandoning that small section.... Also, trying to find the best place to buy the windlace and I assume the rubber trim that is sandwiched on the main door with the windlace. (Pic shows my groovy wine colored lace and the white trim piece). I think I will replace all the white trim pieces on the rehab project. Quote
haymak3r Posted December 6, 2022 Report Posted December 6, 2022 Gotta love that color. Your's looks to be in better shape than mine right there.. Some day, I will get to enjoy replacing this too. lol. Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.