AVDB

In the configuration mode, please take a picture of the COM 1 and COM 2 settings -> squelch threshold for 25 kHz and 8,33kHz channel spacing

try at the end, when all the previous actions will not give the proper effect go to Configuration Mode -> GMA 1347 Configuration Page -> change Master Avionics Squelch

From Diamond DA40NG wiring diagram of G1000 system which is near to me right now, and I can with a fatness of 99% also say that this is true for other G1000 equipped aircraft - GIA 63(W) is the central ‘Integrated Avionics Unit’ (IAU) to the G1000 system. The GIA 63(W) functions as a main communications hub, linking most LRUs with the PFD and MFD displays. The GIA 63(W) contains the GPS (WAAS) receiver, VHF COM/NAV receivers, and system integration microprocessors. It is powered up via two appropriate circuit breakers GPS/NAV 1(2) and COM 1(2) - GEA 71 - LRU that is responsible for receiving/processing signals from engine and airframe sensors) GEA 71 communicates directly with both GIA 63(W)s using RS-485 digital interface it is powered up via one circuit breaker - ENG INST On Seneca this C/B calls GEA, because two engine are installed, we see GEA 1 and GEA 2 C/B on circuit breaker panel.

International db, cycle 2403 is successfully loaded

SVT Enablement Card for G500TXi P/N 010-03716-46 $1,400.00 shipping charges is included

Used, workable (checked today by loading db) Current database cycle 2402 is loaded (few updates left from the annual subscription) Coverage: International Price: $200 obo Preferable for EU aviators

There is info from G3X Touch Certified Part 23 AML STC Installation Manual, 190-02472-01, Rev. 2 concerning your question (EIS display is highlighted in yellow):

Send me PM if you need GFC 500 Autopilot with Electronic Stability and Protection, Part 23 AML STC Installation Manual, 190-02291-00, Rev. 24

Hello Ed, There is only one TAS page which is available for pilot in G1000 normal operational mode - Traffic Map Page From G1000 Pilot's Guide: "Displaying traffic on the Traffic Map Page: 1) Turn the large FMS Knob to select the Map Page Group. 2) Turn the small FMS Knob to select the Traffic Map Page." If we are talking about audio alerts setup - it is available in Configuration Mode only. From G1000 System Maintenance Manual: "To enter configuration mode: 1. Press and hold the ENT key on the PFD while applying power. Release the ENT key after ‘INITIALIZING SYSTEM’ is displayed in the upper left corner of the PFD. 2. Repeat step 1 for the MFD and PFD2 (if installed). The System Status Page (Figure 4-1) is displayed on the MFD and the PFD. 4.2.1 User Interface Once the G1000 is placed in configuration mode, the large and small FMS knob is used to cycle through the different configuration pages, to change page groups, and to change pages in a group. The FMS knob is also used to perform the following: • To activate the cursor press the small FMS knob. • To cycle the cursor through different data fields rotate the large FMS knob. • To change the contents of a highlighted data field rotate the small FMS knob. This action displays an options menu for the particular field, or in some cases, allows the user to enter data for the field. • To confirm a selection press the ENT key. To cancel a selection, press the small FMS knob. Pressing the small FMS knob again turns the cursor off. The CLR key can also be used to cancel a selection or turn the cursor off." In Configuration mode, on PFD, go to System page group -> Audio Alert Configuration page As this page is not shown in G1000 MM, for the purpose of training, please make a screenshot and load it in this post. TAS alert volume settings have to be there. Note: When G1000 system is powered up in Configuration Mode, the system may sound an Audio Warning Tone. This tone can be silenced by using the following steps: on MFD: - rotate Large FMS knob to the right to select GDU group page - rotate Small FMS knob to find Alert Configuration page - Across the button of display are the softkeys. Locate the button under the letters ACK for acknowledge and press the soft key This should stop the chiming of the audio warning system Regards, AVDB

Interconnection wiring diagram GTN 650 as GPS1/NAV1 system, GNS 430W as GPS2/NAV2 system GI 275 Configuration GTN 650 / GNS 430W Configuration Few words about TAWS Few words about WEATHER / TRAFFIC

From Maintenance Manual: "Select the GRS/GMU Calibration page and enter the following softkey password: a) 9 b) 10 c) 11 d) 12 (Far Right softkey)" During calibration, taxi the aircraft in a good BIG nice circle - you will get smooth and precise taxiing G1000 Magnetometer calibration.pdf

Please attach photo of physical GMU 11 installation Make sure that GMU location meet all installation requirements. if it is required - replace metal fasteners into stainless steel perform Magnetic Interference Test my advice: During calibration, taxi the aircraft in a good BIG nice circle - you will get smooth and precise taxiing Magnetometer Calibration.pdf GMU location requirement, magnetic interference.pdf

Hi Ptsticks, Please specify or attache screenshots with GTX 345, GTS 325 and G1000 system. I recommend to check configurations first of all. The best manual which helps you with this issue is GTX 3XX Part 23 AML STC Installation Manual, 190-00734-10. There is description of GTX 345 configuration, taking presence of GTS and G1000 system into account. page 169.pdf

Hope it helps

Hi, Oil pressure and all other engine sensors are connected to GEA 24 or GEA 110 Engine Adapter, collected info from the engine sensors is sent to GI 275 via RS-232 or RS-485 respectively. Please specify which engine adapter you have on board?

1) Go to Configuration Mode (with the GTN turned off, press and hold the HOME key and apply power to the GTN. Release the HOME key when the display activates and the Garmin logo appears fully lit on the screen. ) 2) Touch GTN Setup 3) Touch Ownship 4) Touch Color Ownship 5) Switch off GTN

I’m selling G1000 10xx SAR Unlock Card, P/N 010-00330-52 left unused from a my previous project FAA Form 8130-3 was lost in wartime At https://ww2.txtav.com new card costs $1,036.80. I'm asking $550 The Card is in Kyiv, US shipping and strong technical support included. Related documents: Garmin G1000 Search and Rescue Pilot’s Guide https://www.gocivilairpatrol.com/media/cms/Garmin_SAR_Software_Pilots_Guide_AAC776EBBA500.pdf Garmin Integrated Avionics System Search and Rescue Pilot’s Guide, 190-00760-00 Rev. D https://static.garmin.com/pumac/190-00760-00_d.pdf Garmin SAR Detailed Demo Tutorial https://savannah.cap.gov/media/cms/G1000GarminSARUSGrid_BC2FA7D9482AC.pdf

Tom, According to the 190-00907-00, G1000 System Maintenance Manual, Page 5-109 you can see what values of airspeed parameters are specified for your aircraft: - GLIDE - Vfe - Vne - Vr - Vs1 - Vx - Vy Screenshot from MM is attached as example of this page (Cessna T206H aircraft configuration is shown). In Config Mode on PFD, use the large FMS knob to navigate to the GDU page group, use the small FMS knob to navigate to Airframe Configuration Page. MM says "The data on this page is protected and cannot be changed."

Please see attached GTN Xi Series TSO Installation Manual, 190-02327-02 Please note: it is not current rev. GrmnGTN750Xi_tso_190-02327-02_04.pdf GrmnGTN750Xi_tso_190-02327-02_04.pdf

Are there any red X in System Status Page? What error messages do you have? I recommend to use both G1000 Maintenance Manual for Mooney, doc # 190-00638-01 and the one for STANDARD PISTON/TURBOPROP AIRCRAFT, doc # 190-00907-00, which are available for downloading from Garmin official website. See GIA 63 and GMA 1347 Troubleshooting sections. From my experience, first of all clean GIA 63 #1, GMA 1347 D-Sub and coax cable BNC connectors by LPS MICRO-X CONTACT CLEANER or analog, and test COM 1 once again. Please note that COM antenna MUST always be connected to GIA 63 LRU. Transmitting without an antenna can damage VHF COM transmission path of GIA 63.

Hector, Do pos 3 and 4 come with FAA FORM 8130-3?

Mooneyspace test ok! Pronounced like G1000 system’s the famous message: "TAWS System Test OK"

Neilpilot, is your Skybound G2 is still available? if yes, please send me PM Regards, AVDB