Jump to content

7.Mooney.Driver.0

Basic Member
 View Profile  See their activity

  • Posts

    152

  • Joined

  • Last visited

 Content Type 

Everything posted by 7.Mooney.Driver.0

  1. 7.Mooney.Driver.0
    You can buy a new panel for $156 https://vantageassoc.com/lh-instr-panel-airplanes-mooney-m20-1955-m20-1002-thru-1200-k820244-005.html Sent from my iPhone using Tapatalk
  2. 7.Mooney.Driver.0
    Your A&P/IA not comfortable doing it? It doesn’t have to be a shop. Sent from my iPhone using Tapatalk
  3. 7.Mooney.Driver.0
    I’m based out of SFB and own a 1970 M20C. I highly recommend AirWerks LLC. They are located at SFB, and the mechanic, who is also the owner, owns a Mooney M20C as well. Sent from my iPhone using Tapatalk
  4. 7.Mooney.Driver.0
    AirWerks llc, they are located at KSFB. Owners are Mooney drivers as well. Sent from my iPhone using Tapatalk
  5. 7.Mooney.Driver.0
    We seen this before, this is due to improper wiring. Some installers are very very sloppy when it comes to crimping pins. Have a knowledgeable shop or installer verify the wiring at the GMC 500 connector and at the switch itself. Sent from my iPhone using Tapatalk
  6. 7.Mooney.Driver.0
    Garmin has only granted permission to dealers to use their STC. You would need to find a dealer who is comfortable with your work to sell you the brackets, and give you access to their manuals. Unfortunately, not many dealers are willing to work with owners when it comes to Garmin stuff. The GFC500 is worth every penny. I have one in my C model and love it. Sent from my iPhone using Tapatalk
  7. 7.Mooney.Driver.0
    I would recommend leveling the airplane and completing the calibration that way. You can’t account for panel tilt if you input the degrees from rivet line. Below is my set up, this is what calibration looks like with aircraft level vs what rivet line showed with aircraft off jacks, and how it looks flying. Hope this helps.
  8. 7.Mooney.Driver.0
    That looks like your Lo/Hi vacuum sensor. That line should be connected to your vacuum system, otherwise you’ll get a low vacuum light on. Sent from my iPhone using Tapatalk
  9. 7.Mooney.Driver.0
    Try Airwerks located in SFB. The shop owners are A&P/IAs and Mooney owners/ pilots. https://www.airwerksmx.com Sent from my iPhone using Tapatalk
  10. 7.Mooney.Driver.0
    Your best option is to install it on the Avionics shelf in the back. Sent from my iPhone using Tapatalk
  11. 7.Mooney.Driver.0
    Got mine from them. Very happy with final product. https://www.aircrafthose.com/kits/m20c Sent from my iPhone using Tapatalk
  12. 7.Mooney.Driver.0
    Temp sensor gets installed on the front of the carburetor. Sent from my iPhone using Tapatalk
  13. 7.Mooney.Driver.0
    Thats a marker beacon antenna. Sent from my iPhone using Tapatalk
  14. 7.Mooney.Driver.0
    Like other have said, 2 amps seem very low. What comm radio do you have? Sent from my iPhone using Tapatalk
  15. 7.Mooney.Driver.0
    Hello, hope this helps. I had the same issue and it turned out to be a bad diode. Sent from my iPhone using Tapatalk
  16. 7.Mooney.Driver.0
    The P.T.T is usually wired to the microphone jack (smaller of the two) Tip and sleeve legs. http://www.aeroelectric.com/articles/micjack/micjack.html Sent from my iPhone using Tapatalk
  17. 7.Mooney.Driver.0
    This document might answer your question. https://static.garmin.com/pumac/190-00356-39_A.pdf Sent from my iPhone using Tapatalk
  18. 7.Mooney.Driver.0
    I had to repair mine not long ago. Here are the WD for them. Good luck. Sent from my iPhone using Tapatalk
  19. 7.Mooney.Driver.0
    AMI Aviation located in KSFB. Call and ask for Brad. Sent from my iPhone using Tapatalk
  20. 7.Mooney.Driver.0
    Sent from my iPhone using Tapatalk
  21. 7.Mooney.Driver.0
    Not my Mooney but hope this helps. Sent from my iPhone using Tapatalk
  22. 7.Mooney.Driver.0
    I don’t have what you are looking for but, I’m on the process of redoing my instrument panel. I had the cad file cut out of clear acrylic first, corrected measurements on auto cad and then sent it to the shop to get it cut.. Sendcutsend will cut the panel out of acrylic for $85 thats with shipping. I hope this helps. Sent from my iPhone using Tapatalk
  23. 7.Mooney.Driver.0
    Such a small world. I actually got to see the installation on your airplane. I took mine in for IFR cert not long ago and your was there being worked on, they mention the owner was out of ORL. Sent from my iPhone using Tapatalk
  24. 7.Mooney.Driver.0
    What shop did you use for the installation? Sent from my iPhone using Tapatalk
  25. 7.Mooney.Driver.0
    Does anyone have CAD drawing of instrument panel for 1969-1970 M20 they can share? I’m doing dual G5 upgrade and would like to do one complete panel. TIA Sent from my iPhone using Tapatalk
×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.