Search the Community

I have 1964 M20E and I'm thinking about installing a GoPro 9 somewhere on the outside of my Mooney. Any suggestions as to where and how to mount the camera? Thanks everyone

I know a few of you have made aviation related videos. I have as well. I decided to make more videos and upgrade my GoPro 2 to a couple of GoPro 5 Blacks. The GoPro 2 audio cable that I had been using was really robust and the audio quality was exceptional. I bought what I thought was an audio kit for the 5 Blacks and am having a bear of a time figuring out how to get it to work correctly. I purchased this from Amazon: https://www.amazon.com/gp/product/B01MT3Q50Y/ref=ppx_od_dt_b_asin_title_s00?ie=UTF8&psc=1 Visiting the GoPro site, I see what I bought was an external microphone adapter that GoPro sells for connecting to external mics and that Nflightcam attaches their audio cable to it. I found one Amazon commenter who said Nflightcam told him to use the line in for the audio input (like GoPro provides several options for mics when you connect the adapter). Like the commenter, I found the volume was extremely low. Haven't put it through the editor yet to see how much I can boost it. There are a number of other input settings (Std Mic, Power Mic, Power Mic+, etc), but they all have an annoying background noise. In addition, I found that when using the USB-C charging cable input, it would charge if the GoPro was off, once powered, the battery was no longer charging. Here is an example video using one of the audio input settings. If you listen closely, you can hear the background static. I will post a couple others as well when I upload them.

I know a few of you are using GoPros for flight videos. I recently purchased a GoPro Hero 5 to add to my GoPro Hero 2. With the 2, I have been using a standard audio jack connection to the GoPro 2 but noticed that it only records on 1 channel from my audio panel. Have any of you purchased an audio cable for a GoPro Hero 5 and have a recommendation for one that will work with the PS Engineering stereo output?

I know a few of us are running GoPros on the exterior of our aircraft, some by the use of the included sticky mount. Here is a little unknown mount many people aren't aware of, the surfboard mount My girlfriend and I purchased a kayak so of course I want to get some watersport videos. I bought a floaty back door and a surfboard mount so I can do an underwater and hull shot. BUT! I happen to notice the included mounts are QUITE larger than the standard black mounts that come with our camera. How much larger? Well after some lengthy math calculation (I hate math) I've found that the standard surfboard mount (just the larger one pictured above, I'm not counting the tether mount) is 43% larger than the standard mount. Now. How does that equate into safety for our cameras? Well, I did a little research (I started this 'project' at 10pm and it's now 2am, don't worry, I'm bored at work). On the back of the mounts, we are greeted by this: A quick search turns up 3M's technical data on ALL of their adhesive products (located HERE). Lets learn us some MooneySpace knowledge! (Please bear with me, I shamelessly copypasted some 3M articles): The 3M VHB (or Very High Bond) is one of 3M's strongest adhesive material. The material that GoPro spec's out for its mounts is Product number 4991, skinned to a thickness of 0.090" or 2.3mm. This family utilizes multi-purpose acrylic adhesive on both sides of a conformable adhesive foam core. The adhesive provides excellent adhesion to a broad range of high and medium surface energy substrates including metals, glass, and a wide variety of plastics, as well as plasticized vinyl. The conformable adhesive foam core provides good contact, even with mismatched substrates. Aluminum is one of the BEST substrates that this material can be mated to. In their included .pfd of material is A LOT of good stuff. Two things we want to pay attention are these: Normal tensile strength (aka pulling vertical, as in off a desk), and then dynamic overlap shear, (aka sliding across said desk). In the above report, 3M utilizes the ASTM D-897 testing method for tensile and ASTM D-1102 for the dynamic overlap shear. In those, they test in stringent conditions for temp, moisture, and a constant rate at which the force is applied. So keep this simple the results are as follows; 4991 is rated at 70 lbs/sq in for tensile strength and 65 lbs/sq in for shear. Going back to our basic area of the above mounts, the stock GoPro mount is about 2.8 sq in, while the surfboard mount is about 4.0 sq in, both give or take a tenth or two. If I'm not screwing up my math, a simple multiplication table gives us a the following results: Surfboard tensile = 280lbs Surfboard shear = 260lbs Stock tensile = 196lbs Stock shear = 182lbs I do not have any sort of knowledge of fluid dynamics or physics, so if anyone here does and could run a calculation on how much drag a GoPro and mount produce, that would be pretty sweet. But I think it's safe to say our cameras are not producing any sort of drag number listed above. If you want the extra security, you can upgrade to the surfboard mounts (the cheapest place I found them is HERE ). ----------------------------------------------------------------------------------------------------------------------------- Now, on a separate tangent, if some of you have decided to try out the sticky mount, I'd like to highlight the recommendations from 3M as posted below: Time: After application, the bond strength will increase as the adhesive flows onto the surface (also referred to as “wet out”). At room temperature approximately 50% of ultimate bond strength will be achieved after 20 minutes, 90% after 24 hours and 100% after 72 hours. This flow is faster at higher temperatures and slower at lower temperatures. Ultimate bond strength can be achieved more quickly (and in some cases bond strength can be increased) by exposure of the bond to elevated temperatures (e.g. 150°F [66°C] for 1 hour). This can provide better adhesive wetout onto the substrates. Pressure: Bond strength is dependent upon the amount of adhesive-to-surface contact developed. Firm application pressure develops better adhesive contact and helps improve bond strength. Typically, good surface contact can be attained by applying enough pressure to ensure that the tape experiences approximately 15 psi (100 kPa) pressure. Either roller or platen pressure can be used. Note that rigid surfaces may require 2 or 3 times that much pressure to make the tape experience 15 psi. Temperature: Ideal application temperature range is 70°F to 100°F (21°C to 38°C). Pressure sensitive adhesives use viscous flow to achieve substrate contact area. Minimum suggested application temperatures is 60*F for 4991. To obtain good performance with all 3M™ VHB™ Tapes, it is important to ensure that the surfaces are dry and free of condensed moisture. Clean: Most substrates are best prepared by cleaning with a 50:50 mixture of isopropyl alcohol (IPA*) and water prior to applying 3M™ VHB™ Tapes. Shelf Life: All 3M™ VHB™ Tapes have a shelf life of 24 months from date of shipment when stored at 40°F to 100°F (4°C to 38°C) and 0-95% relative humidity. The optimum storage conditions are 72°F (22°C) and 50% relative humidity. The performance of tapes is not projected to change even after shelf life expires; however, 3M does suggest that 3M™ VHB™ Tapes are used prior to the shelf life date whenever possible.

It was supposed to be raining all day. So we thought we'd spend the day in the hanger working on some little projects. Of course, the forecast was probably a day off and the rain will likely be here tomorrow. I've wanted a couple of good, new, fresh GoPro mount points on the plane. And I also wanted a better solution to the cockpit interior GoPro mount. The cockpit mount is a U-bolt over the center roof cage member, just aft of the rear eye-vents. The tail mount is a sticky mount on the front right corner of the horizontal stabilizer. The belly mount is a sticky mount on the tail skid. I'll try to post pictures of the mounts tomorrow. But here is the view from each. I like the view angle from each except the cockpit-cam. I think it shows too much roof and should be lowered slightly. I'll try again tomorrow.

Two videos of our flyaway with some friends in April this year. The first one is from inside of the cockpit and doesn't show much of the outside. It has radio work, etc. https://youtu.be/VacC9aNIFW4 The second one is a low level flight to a fuel stop en-route on the second day: https://youtu.be/vGYeEpag2Mo Please hit LIKE if you like them Sorry about the quality. I thought I had figured out this gopro to youtube stuff, etc but I guess not Tony

Okay last one for now. Just enjoying the GoPro. Feedback welcome (good or bad obviously). http://www.youtube.com/watch?v=v1xuOHeWu8o