mooney2201
-
Posts
108 -
Joined
-
Last visited
Content Type
Profiles
Forums
Blogs
Gallery
Downloads
Media Demo
Events
Everything posted by mooney2201
-
Running oil stains on nose gear door
mooney2201 replied to Lax291's topic in Modern Mooney Discussion
You probably still have one or more leaking...I've had my m20j for 29 years .you must completely degrease the engine..start with a pristine clean engine...you will find the leak..just take your time -
Your are right about it being bulky between the seats..I had the same problem .. remedy was I got small rubber bungy hold down clips, added clips under the seat and pulled excess under the seat...they do make a great cover..extremely comfortable to me
-
Running oil stains on nose gear door
mooney2201 replied to Lax291's topic in Modern Mooney Discussion
I have found that oil return lines cause this problem, Followed by valve cover gaskets -
-
What does this capacitor do
-
I have leather yokes on my m20j. Can anyone recommend what to put on the leather to keep it looking great.
-
I HAVE A VERY LIGHT ALTERNATOR WHINE IN MY M20J....Any suggestions on how to get rid of it...I have a lonestar capacitor on the alternator just doesn't seem to work. Its coming in on my headsets.
-
Has anyone removed their annunciator...I have a jpi 930 which is stc,d to remove old guages...I want to replace gear down annunciator...with green l.e.d. light....and gear unsafe with red l.e.d. Can this be done legally
-
I believe there are two of these bearing housings...trim wheel and in the back near jackscrew
-
Has anyone ever serviced the main bearings in the trim wheel housing. I don't want to remove the side housing and have everything spring out at me..I don't think they have ever been greased before...does the grease get hard.
-
Ok thankyou ☺
-
You must save everything to configure module...or you will loose all settings, and I don't need that aggravation to redo all the settings
-
Golf coast avionics.. Said it would be $35 for the battery. And a 150 labor
-
Has anybody replaced the battery in their gtn 750..How much does garmin charge
-
How often should a slick harness be replaced in years
-
What is the proper torque value on mcculley prop governor..on io 360 a3b6...the 4 nuts on governor
-
Has anyone ever performed engine installation buy removing engine mount first...and then bolting the mount to the engine, which gives you plenty of room...than bolting engine mount from the bottom of the firewall And swinging it into place If so how hard was this installation
-
Wondering if anyone is using Teflon spray on heim bearings on the landing gear...oil seem to attract dirt
-
I have a 1978 M20J. I would like to make the yolks look new again. They are original,But are not powder coated, seems to have a plastic hard coating on them. Does anyone know if they can be stripped and powder coated..I really don't want to have them wrapped in leather..
-
I would like to remove my center console to have it painted..Its sun faded.Just don't know if its a bear to remove...1978 m20j
-
Both wing strobes suddenly no longer work
mooney2201 replied to FlyBoyM20J's topic in Modern Mooney Discussion
I may have the Hoskins controllers.. I switched to led strobes And yes one bad strobe will knock out the other.. Give me a phone number and I will call you tomorrow and let you know that I have all the parts you need -
Does anyone know the king ROLL servo part number for the 1978 m20j kfc 200
-
Besides the cutoff switches on the flap motor are there any other relays on 1978 m20j
-
Does anybody have a part number to replace roller cutoff switches. Flaps failed today, removed belly panel,and of course they started working.I am sure its cutoff switch.. Thanks gary
-
can anyone tell me the easiest way to remove engine oil screen, on the back bottom of the engine...IO360a3b6 cant seem to get my hands anywhere near the socket
