CDF219 Posted April 9, 2020 Report Posted April 9, 2020 I have a 66E and I have redone entire interior, Last thing is the yokes. How do you get these things off? I see the set screw and the bolt that goes through top to bottom. Any suggestions? thank you in advance. Quote
cliffy Posted April 9, 2020 Report Posted April 9, 2020 You might ask your A%P to look at it and do the required AD on cracks in the control wheel at the same time. Its a dye penetrant inspection that is easy (but messy) to do. Quote
CDF219 Posted April 9, 2020 Author Report Posted April 9, 2020 Its in annual now and no mention of that AD Quote
cliffy Posted April 9, 2020 Report Posted April 9, 2020 (edited) AD 77-17-04 Control Wheel Shaft Inspection Every 500 hrs If you have the wheels off its easy to do the inspection BUT messy Edited April 9, 2020 by cliffy Quote
Guest Posted April 9, 2020 Report Posted April 9, 2020 5 hours ago, CDF219 said: I have a 66E and I have redone entire interior, Last thing is the yokes. How do you get these things off? I see the set screw and the bolt that goes through top to bottom. Any suggestions? thank you in advance. Normally the wheel is held to the shaft with a taper pin. If so back the nut until it’s flush with the end of the thread, support the pin end with a bucking bar against the wheel beside the pin, with your second and third hands drive the nut with a hammer to loosen the pin. Remove the pin and loosen the set screw and remove the wheel from the shaft. Clarence Quote
carusoam Posted April 10, 2020 Report Posted April 10, 2020 Where are you sending the yokes afterwards? Many visit the same leather interior shop in TX.... Might be a one stop shop for all things that the yokes would need... Best regards, -a- Quote
RobertGary1 Posted April 10, 2020 Report Posted April 10, 2020 In addition there is a set screw. -Robert Quote
gsxrpilot Posted April 10, 2020 Report Posted April 10, 2020 9 hours ago, carusoam said: Where are you sending the yokes afterwards? Many visit the same leather interior shop in TX.... Might be a one stop shop for all things that the yokes would need... Best regards, -a- Yep, AeroComfort in San Antonio is where you want to send them. Hector is the best there is when it comes to putting leather in a Mooney. I've put his handiwork in both of my Mooneys and get complements on the yokes all the time. https://aerocomfort.com N6XM - M20C N252AD - M20K 252 1 Quote
PTK Posted April 10, 2020 Report Posted April 10, 2020 11 hours ago, carusoam said: Where are you sending the yokes afterwards? Many visit the same leather interior shop in TX.... Might be a one stop shop for all things that the yokes would need... Best regards, -a- No need to send them across the country and pay hundreds for the privilege! Yokes are easy to do yourself. I did mine with leather I had left over from interior. 9 1 Quote
carusoam Posted April 10, 2020 Report Posted April 10, 2020 You have to see Peter’s handiwork in person... Its like he has fine craftsman skills And is good working in tight places... His M20J looks brand new from the inside out... or outside in.. for that matter... Best regards, -a- 1 Quote
CharlesHuddleston Posted April 10, 2020 Report Posted April 10, 2020 5 hours ago, PTK said: No need to send them across the country and pay hundreds for the privilege! Yokes are easy to do yourself. I did mine with leather I had left over from interior. Did you remove them to recover, or recover in place? They look great. Quote
PTK Posted April 10, 2020 Report Posted April 10, 2020 1 hour ago, CharlesHuddleston said: Did you remove them to recover, or recover in place? They look great. Removed, cleaned, primed and applied two coats of protective paint. Then covered with leather. Quote
Wes Posted April 11, 2020 Report Posted April 11, 2020 Be verrry careful if you try to drive the tapered pin out with a hammer. They make a tool to remove it. It costs about as much as the repair of the jeweled clock in the pilot side yoke...providing you don't damage the yoke in the process. Ask me how I know this. Education costs money... and I went to school! The good news is...i graduated....i don't use a hammer any more. And by the way, you don't have to tap it very hard to cost yourself a lot of money, headaches, and time. Just saying. Quote
CDF219 Posted April 11, 2020 Author Report Posted April 11, 2020 Thank you all. For those that had them done, they look amazing. Who did them and at what cost? Quote
RLCarter Posted April 11, 2020 Report Posted April 11, 2020 Had mine done at a local HotRod upholstery shop. I prepped, painted and ran the wires for the PTT switches and sent them over, 1 wk and 100 bucks later it was done 1 Quote
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.