Jump to content

Mooney Bladder Install


N6758N

Recommended Posts

I figured I would start a thread to document the installation of bladders in my C model, I do not believe such a thread exists here yet but someone please correct me otherwise. I will update this thread as I have time to work on the project. I obtained a set of serviceable bladders (54.8 gals) from AirMods, and I purchased the STC and a few misc parts needed to complete the job from Griggs aircraft. I just started the job this weekend so progress will be slow. 

 

IMG_9344.thumb.JPG.9f771b2d0b3d649294f8504ef4bffd71.JPG

IMG_9345.thumb.JPG.f570b9bee3630f813a63764044dcd7ae.JPG

IMG_9346.thumb.JPG.d48bc8b68c05ac3db9cd7724870ea879.JPG Here is the bladder setup as it will be installed inside the wing, I am going to be using the new style caps.

IMG_9359.thumb.JPG.a6e163738edb906b5eedb9000e75b4a8.JPGFuel senders have been removed, I will be using the new CiES senders in their place. 

IMG_9349.thumb.JPG.518db58954717e3a6d31b00e93ba9125.JPG

IMG_9351.thumb.JPG.3e88c084fd274918c30f5e9f2a3d95a0.JPGTemplates for the new holes that have to be cut in the wing. 

IMG_9350.thumb.JPG.d028133eb950a0e121954b419b0f0d2e.JPG

IMG_9353.thumb.JPG.6cc129b0c680724e9b9e0c35b8ebebea.JPGTemplate laid out, a little tricky figuring out how to make a hole with a 1.5 radius curve.

IMG_9354.thumb.JPG.7391976ca0bcf9310782e561653bebc3.JPGCutting into the wings, no turning back now!

IMG_9355.thumb.JPG.cec08b2423b21ec5bc7f1230f2e999b9.JPG

IMG_9357.thumb.JPG.a2823c67e96c9b537d2a921739fb520c.JPG

IMG_9358.thumb.JPG.9b741f9105ea7a89c0ae45eab8b6a78f.JPG

  • Like 4
Link to comment
Share on other sites

4 hours ago, Piloto said:

 I would pressure test for leaks before installing them. Just apply air pressure (5psi) and check for bubbles while spraying water around.

José

Good idea Jose', although I think 5 psi would be a little high. Can anyone give some helpful suggestions on how to remove the fuel access panels on top of the wing? Mine have never been removed in almost 50 years as far as I can tell and they are stubborn...

Link to comment
Share on other sites

9 minutes ago, N6758N said:

Good idea Jose', although I think 5 psi would be a little high. Can anyone give some helpful suggestions on how to remove the fuel access panels on top of the wing? Mine have never been removed in almost 50 years as far as I can tell and they are stubborn...

http://www.aircraft-tool.com/shop/detail.aspx?PRODUCT_ID=15048

Link to comment
Share on other sites

2 hours ago, N6758N said:

Good idea Jose', although I think 5 psi would be a little high. Can anyone give some helpful suggestions on how to remove the fuel access panels on top of the wing? Mine have never been removed in almost 50 years as far as I can tell and they are stubborn...

You can pressure test with just air from your mouth.

To easily remove the tank access panels:

1. Remove all the screws

2. Insert a thin bladed knife with rounded tip between the skin edge and the cover groove.

3. Jig saw the knife while moving across the perimeter to cut the sealant.

4. The access panel will just fall out after cutting the sealant.

José

 

Edited by Piloto
Link to comment
Share on other sites

6 minutes ago, Piloto said:

You can pressure test with just air from your mouth.

To easily remove the tank access panels:

1. Remove all the screws

2. Insert a thin bladed knife with rounded tip between the skin edge and the cover groove.

3. Jig saw the knife while moving across the perimeter to cut the sealant.

4. The access panel will just fall out after cutting the sealant.

José

 

Jose',

Do you think a butter knife would work for this?

Link to comment
Share on other sites

On 8/21/2017 at 8:44 AM, Piloto said:

 I would pressure test for leaks before installing them. Just apply air pressure (5psi) and check for bubbles while spraying water around.

José

Water? Is soapy water with mild dish soap better? Makes bigger bubbles.

Link to comment
Share on other sites

More slow progress last night, finally got all the fuel panels removed. Does anyone have any old fuel access panels they are willing to part with? I need two more to complete the job, they will go where the old filler caps were. 

 

IMG_9380.JPG

IMG_9379.JPG

Link to comment
Share on other sites

1 minute ago, Bob_Belville said:

  Access panels: try @LASAR, or Paul Loewen who kept a lot of used parts when he sold LASAR, or Jerry Pressley who is on MS as aircraftpartswholesale or similar.

Thanks Bob, I'm waiting to see if @Alan Fox has any, and then I will try others. I can always remove the old plate off the doubler and fabricate a new one without the hole, but I'm trying to save myself a few steps if I can. 

Link to comment
Share on other sites

12 minutes ago, Bob_Belville said:

  Access panels: try @LASAR, or Paul Loewen who kept a lot of used parts when he sold LASAR, or Jerry Pressley who is on MS as aircraftpartswholesale or similar.

@N6758N We have fuel access panels in stock. List price on new ones is $481.24. We have 2 used ones for $210.00 each. Dan's direct line in parts is: 800-954-5619. Nice work!

Link to comment
Share on other sites

Just now, LASAR said:

@N6758N We have fuel access panels in stock. List price on new ones is $481.24. We have 2 used ones for $210.00 each. Dan's direct line in parts is: 800-954-5619. Nice work!

Thanks guys, I think I will pass on those prices though. I can easily make a new one out of the old filler plate access panel doubler for about $10 worth of materials. Thanks for checking in though!

Link to comment
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.