RLCarter Posted January 8, 2019 Report Share Posted January 8, 2019 1 minute ago, Mike Ropers said: I'd vote aluminum - plasti dip coat the edge for scratch protection - it can be sprayed for an even coating. I would think the aluminum would have to be 3/16 or better for rigidly, they look to be about 36" long but I'm not real sure, my software can nest multiples pieces but wasted material on a production run or 1 set would be high. A protective material on the pad of plastic, rubber or even masking tape on the control would work just fine. For production I would use a Laser or Router, Water-Jets do not cut 90° to the surface and Lasers do not like reflective surfaces (aluminum, stainless) which you can mask but it does add to the process Quote Link to comment Share on other sites More sharing options...
0TreeLemur Posted January 8, 2019 Report Share Posted January 8, 2019 On 1/6/2019 at 12:23 AM, Tres said: Does anybody have a copy of these they can post? The dropbox link gives a 404 error and the file attached to the message is corrupt. Thank you If instead of clicking on the dropbox link, you click on "travel_boards.zip", you will download a zip file. When I unzip it, it seems to be corrupt. The only files extracted are: "rudder instructions.zip" and "rudder.jpg". Maybe somebody else can extract more. Luckily all I need right now are the rudder checks. I'll upload these two rudder files that I did get out of the zip file to the Downloads section. Given that the zip file is 1.9 MB and the two .jpg files are about that size, I'm guessing that is all it contains. Quote Link to comment Share on other sites More sharing options...
Tres Posted January 13, 2019 Report Share Posted January 13, 2019 I have the CNC tools to make these and would be happy to make extras and sell them at cost if I could get the profiles. I have a 4'x8' laser that would be perfect. There are also multiple online fabrication services that could quickly cut these with the right cad data. If anyone has scans I can digitize them and start cutting. 3 Quote Link to comment Share on other sites More sharing options...
M20F-1968 Posted January 13, 2019 Report Share Posted January 13, 2019 On 1/8/2019 at 10:29 AM, Mike Ropers said: I'd vote aluminum - plasti dip coat the edge for scratch protection - it can be sprayed for an even coating. You would not want to put any sort of coating of the edge of the travel boards. There is enough to go wrong when copying them, this would just add another possible source of error. They are quite long so any error is magnified. John Breda Quote Link to comment Share on other sites More sharing options...
Sabremech Posted January 14, 2019 Report Share Posted January 14, 2019 36 minutes ago, M20F-1968 said: You would not want to put any sort of coating of the edge of the travel boards. There is enough to go wrong when copying them, this would just add another possible source of error. They are quite long so any error is magnified. John Breda Not to mention the potential for changing the boards calibration. If they aren’t an exact copy, then the rigging might not end up correct. Quote Link to comment Share on other sites More sharing options...
Guest Posted January 14, 2019 Report Share Posted January 14, 2019 On 1/8/2019 at 11:02 AM, RLCarter said: I would think the aluminum would have to be 3/16 or better for rigidly, they look to be about 36" long but I'm not real sure, my software can nest multiples pieces but wasted material on a production run or 1 set would be high. A protective material on the pad of plastic, rubber or even masking tape on the control would work just fine. For production I would use a Laser or Router, Water-Jets do not cut 90° to the surface and Lasers do not like reflective surfaces (aluminum, stainless) which you can mask but it does add to the process The Mooney boards are 1/4” plywood with aluminum stiffeners for the longer ones. My Cirrus set are cut from aluminum sheet, to prevent scratches I ran a strip of 3M electrical tape along the edges. Clarence Quote Link to comment Share on other sites More sharing options...
RLCarter Posted January 24, 2019 Report Share Posted January 24, 2019 And the thread goes dormant again Quote Link to comment Share on other sites More sharing options...
Sabremech Posted January 24, 2019 Report Share Posted January 24, 2019 I priced having some sets made and was priced right out of it. The calibration of the boards is pricey. David Quote Link to comment Share on other sites More sharing options...
Captnmack Posted January 24, 2019 Report Share Posted January 24, 2019 I have a set in Texas.. Quote Link to comment Share on other sites More sharing options...
Bob_Belville Posted January 24, 2019 Report Share Posted January 24, 2019 On 1/13/2019 at 8:18 PM, M20Doc said: The Mooney boards are 1/4” plywood with aluminum stiffeners for the longer ones. My Cirrus set are cut from aluminum sheet, to prevent scratches I ran a strip of 3M electrical tape along the edges. Clarence Clarence, the (expensive) boards that @AGL Aviationbought from Mooney a few years ago are aluminum. Perhaps the factory has produced both from time to time. Lynn taped the edges that touch the paint. Quote Link to comment Share on other sites More sharing options...
David_H Posted August 11, 2019 Report Share Posted August 11, 2019 I read several threads on travel boards and this one appears to be the most recent on the topic. Was anyone able to come across data that could be used to reproduce the boards? If not, does anyone have a set that could be used to produce a duplicate a set? Quote Link to comment Share on other sites More sharing options...
M20F-1968 Posted August 11, 2019 Report Share Posted August 11, 2019 I have made them and can make them again. The problem is they are very labor intensive to make. You can contact me to discuss. John Breda Quote Link to comment Share on other sites More sharing options...
David_H Posted August 13, 2019 Report Share Posted August 13, 2019 On 8/10/2019 at 9:37 PM, M20F-1968 said: I have made them and can make them again. The problem is they are very labor intensive to make. You can contact me to discuss. John Breda John... I sent you a message with my contact info. Quote Link to comment Share on other sites More sharing options...
EricJ Posted August 14, 2019 Report Share Posted August 14, 2019 Is there a reason not to just get a set properly dimensioned for drawings or files so that whoever needs a set could them water-jetted or something? Quote Link to comment Share on other sites More sharing options...
carusoam Posted August 14, 2019 Report Share Posted August 14, 2019 A great question to pose to Kevin at Mooney... Best regards, -a- Quote Link to comment Share on other sites More sharing options...
David_H Posted August 14, 2019 Report Share Posted August 14, 2019 17 minutes ago, EricJ said: Is there a reason not to just get a set properly dimensioned for drawings or files so that whoever needs a set could them water-jetted or something? In my mind, putting the files out there so others can make their own boards is the ideal scenario. Generating a set of engineering drawings so others can reproduce the boards isn't an issue. Either obtaining the data to generate the drawings or obtaining a set of travel boards for measurement purposes is required to make it happen. It's surprising that someone hasn't already posted the data needed to make a set. I can't imagine anyone making a fortune owning a set of travel boards. Quote Link to comment Share on other sites More sharing options...
kortopates Posted August 14, 2019 Report Share Posted August 14, 2019 A great question to pose to Kevin at Mooney... Best regards, -a- They can be ordered through Mooney or an MSCSent from my iPhone using Tapatalk 1 Quote Link to comment Share on other sites More sharing options...
RLCarter Posted August 14, 2019 Report Share Posted August 14, 2019 2 hours ago, kortopates said: They can be ordered through Mooney or an MSC Didn't someone on MS say they were $4500.00 a set? Quote Link to comment Share on other sites More sharing options...
David_H Posted August 14, 2019 Report Share Posted August 14, 2019 20 minutes ago, RLCarter said: Didn't someone on MS say they were $4500.00 a set? I haven't personally checked the costs, but could easily see this being true. If so, that much of an "aviation maintenance tax" is appalling on every imaginable level. The engineering for the M20 series was done decades ago. 1 Quote Link to comment Share on other sites More sharing options...
M20F-1968 Posted August 14, 2019 Report Share Posted August 14, 2019 I doubt very much that the factory will freely provide the digital data to make these on a CNC machine. They are using the data they have to make them for sale, for profit by Mooney. I have the models to make them. I can make them one at a time which is labor intensive, or I can use my models to create my own set of data. I will look into the possibilities. John Breda Quote Link to comment Share on other sites More sharing options...
David_H Posted August 14, 2019 Report Share Posted August 14, 2019 18 minutes ago, M20F-1968 said: I doubt very much that the factory will freely provide the digital data to make these on a CNC machine. They are using the data they have to make them for sale, for profit by Mooney. I have the models to make them. I can make them one at a time which is labor intensive, or I can use my models to create my own set of data. I will look into the possibilities. John Breda Just curious... Why would you want to make another set of Travel Boards if you already have a set? Quote Link to comment Share on other sites More sharing options...
M20F-1968 Posted August 15, 2019 Report Share Posted August 15, 2019 6 hours ago, David_H said: Just curious... Why would you want to make another set of Travel Boards if you already have a set? There are Mooney owners that want them who do not have a set. John Breda Quote Link to comment Share on other sites More sharing options...
RLCarter Posted August 15, 2019 Report Share Posted August 15, 2019 If you knew the airfoil profile, isn't "0°" the trailing edge of the cord line? Quote Link to comment Share on other sites More sharing options...
David_H Posted August 15, 2019 Report Share Posted August 15, 2019 1 hour ago, M20F-1968 said: There are Mooney owners that want them who do not have a set. John Breda Very true. Would you be willing to share the data you have? Quote Link to comment Share on other sites More sharing options...
Eight8Victor Posted August 15, 2019 Report Share Posted August 15, 2019 I attempted to create a set via waterjet. My intention was to be able to share the cad file so they could be produced at a local level for whoever needed them. The problem is that both sides have the degree scale and we could only jet the degree scale on one side as it was impossible to set the aluminum back in the precise position to create the degree scale on the opposite side. I ended up marking them by hand with a sharpie. The Mooney boards are very intricate and a work of art. 2 Quote Link to comment Share on other sites More sharing options...
Recommended Posts
Join the conversation
You can post now and register later. If you have an account, sign in now to post with your account.