Jump to content

Leaderboard

Popular Content

Showing content with the highest reputation on 10/25/2019 in all areas

  1. I started following Mooneyspace back around 2010. I was in between Mooneys and followed Parker's 201 and later his 252 with great interest. I got more active when I bought another Mooney in 2014. In times over a 20+ year period I had bought insurance through the AOPA agency, feeling that they were doing the best job of shopping rates for me and presenting options, which I feel that they were back then. I didn't get that feeling in 2014 so I switched to Falcon and really have no complaints, other than that I would send in my annual info in September and would have liked my quotes earlier. Earlier in 2019 when I heard that Parker was going to be an option I planned on getting him to quote me this fall. I met him and his wife in April at Sun N Fun and everything I had heard was true - very sincere, honest people. I let him know when my policy was due and he reached out a few weeks ago. I'm glad I switched. Outstanding experience! Very knowledgeable, very responsive. A huge plus is that he speaks "Mooney". This is an unsolicited endorsement - but give @Parker_Woodruff a shot at your business - you won't be disappointed.
    10 points
  2. In mid September we (wife and I) closed on a 1995 M20J MSE. Since then, it has been in annual and we just came out the other side of that experience only moderately lighter in the wallet. We got the pre-buy and subsequent annual done by Sean at C & W Aero at KCDW. It was a good learning experience but I'm glad it's over. I did the flight from KCDW to KPOU with my CFI yesterday and it was both fun and challenging. On the flight we went through airwork maneuvers: steeps, stalls, slows, constant airspeed descents, AP familiarization, manual gear extension, speedbrake use, and managing energy approaching the destination. As a low timer with DA20 and C172 experience I was amazed how different certain maneuvers felt. For example, steep turns go nose low much more in the Mooney than I am used to. Also, the general cruise attitude of the plane looks different. My CFI was pointing out a tendency to fly more nose-high than I should. I was absolutely amazed at how docile the J felt in stalls (power on and off). There wasn't any strong wing dropping tendency or even much buffeting. I thought about asking to go through accelerated stalls, but maybe another time. I was feeling a little saturated. I thought I had hit the approach numbers pretty good and was 75 knots over the threshold with nearly full nose up trim yet still bounced once and then settled nicely for a smooth but slightly yawing landing. CFI reminded me to avoid the temptation to nose down after bounce and just wait for it to settle as you continue to hold it off the runway. It'll be better next time! It is a joy to fly. I'm excited about getting through the insurance probation period and being free to continue to practice on my own. Thank you MSers for all your words and experience. We definitely made the right choice of aircraft. Photo is me, my father-in-law (retired A&P), and my wife after I returned with my CFI.
    9 points
  3. Light Painting of Maggie in San Diego. Wonderful gift of light painted photos by : Gary Buzel who is a pro photographer and the VP of King Schools [does all the video production]. This was a Montgomery Field in San Diego. Here is Gary's website: https://www.illumigraphic.com/ and https://www.creighphotography.com/ The photo shoot was such a blast. Christmas is coming! My advice: Get a session booked today. Second piece of advice: when able, be a Unicorn!
    5 points
  4. Buy the nicest, newest and fastest plane you can comfortably afford to pay for and maintain.
    4 points
  5. I've seen a few bounces from the ground as an observer. This didn't fee like that. It was more like a stone skipping across a pond. No pitching or rolling around. I was rounding out and felt the wheels gently touch the runway and then I was climbing for a moment. I was about to push in the throttle, but my CFI said "just hold it". It was a 5,000 ft runway and the first contact was at the 1,000 ft marker. Turned off with about 2,000 ft to spare and light braking.
    3 points
  6. Torque it precisely, then lock wire it. Then un-torque it to get the lock wire on, then re-torque it, rinse repeat. And who doesn’t love screwing it on 1/6 of a turn at a time X six bolts. We all must love this aviation thing!
    3 points
  7. After reading through several of the posts on here on installing Shoulder Harnesses on an older short-body Mooney, I figured I'd give back to the community with our process on installing inertial reel shoulder harnesses on our 1965 Mooney M20E. Resources/Reference Threads Which kit we installed, and what to know before you order? We installed the inertial reel shoulder harnesses with lift-lever buckle release from Alpha Aviation: https://alphaaviation.com/mooney-m20-a-thru-k-front-inertial-reel-shoulder-lap-belt-replacement-upgrade-lift-lever-buckle/ . Can't say enough good things about them, they were extremely helpful over the phone and when we lost some of the washers in the included minor change kit (more on that later), they were kind enough to mail me a baggie full at no additional cost. Before you order, you need to know 3 things: What's the attachment point of the seatbelt to the airplane? There are two. Either it is bolted on where a bolt goes through to attach it to the airplane, or it's hooked on, where there's a metal hook clamp at the end of the lap belt that hooks into the metal ring on the seat. What colour do you want? Match the interior. We went with the Fawn, they look great! Push Button or Lift Lever? Personal preference. They say not to use the lift lever with the manual gear, however after a half dozen flights on ours with the Johnson bar I've never had it release on me or cause issues. Now the fun part - installing! Tools Needed: Masking Tape Set of wrenches, if I remember correctly, a 9/16ths and a 5/8ths is what we used the most Handy phillips head screwdriver Slack-jaw pliers Needle-nose pliers Socket head wrench for the bolt (or you can do it with a regular wrench) Cotter pins since you're removing the seat Drill with multiple bits (recommended a rotary ream) Overview Video IMG_2630.MOV Step One Remove the seats. You're going to need the access, and this makes it easier to unhook the old seatbelts anyways. Step Two Pray to Al that the engineers when assembling your particular Mooney gave you a little bit of clearance between the steel bars of the cage and the skin of the aircraft. Okay, now you're ready to get started. Do the pilot's side first, it's by far the hardest, and also the one you're most frequent to use. Step Three Remove the side-plastics on the side you're working on, for this guide, I'm going to focus on the Pilot's side as I recommend to do that one first. Remove the window surrounds - side plastics/paneling around the windows. Remove the headliner. Step Four Now the fun part. Take the clamp, and open the clamp up by inserting a screwdriver into each hole opposite of each other so they make an X, then push against them to open the clamp up so it will fit over the tube. You're going to need to install the clamp, included with the minor change kit, around the structural tube that runs in between the two windows with the flange & screw holes facing aft. This is murder. It is very hard to get the clamp on and turned around and took us probably 3-4 hours to do it. I wish I had advice for you, but there's not really any. What we did was used the needle nose pliers to hold the aluminum around the tube back and then just brute forced it on and kept pushing/turning, pushing/turning until it was where it needed to be. One thing that makes it a little easier - try to find the place with the most clearance between the skin of the aircraft and the tube. For us, it was at the top under the headliner. We worked it on there then just shimmied the clamp down. Step Five Once you finally have it turned around, align the clamp to the vertical midpoint of the two windows, then use those slack-jaw pliers to tighten the clamp. Step Six Now it's time to do a test fit. The minor change kit includes the bolt, washers, spacers, and nut that you'll need. They are going to go through the provided hole on the inertial reel box, then through the two holes on the clamp, affixing the nut on the end of the bolt (spoiler alert: tightening the bolt on to that nut is like doing open heart surgery with swiss army knife tweezers), like so. Step Seven Do a test fit with the bolt through the clamp holes. Is the clamp in the right position or is it too high/too low? Step Eight Take the plastic window surrounds you removed earlier and line it up with the bolt holes on the clamp to determine where you need to drill the hole for the bolt to go through the plastic and into the clamp. It's more of an art than a science and requires some eye-balling. Mask off the hole, then use your drill & rotary ream to drill a hole big enough for the bolt to go through in the plastic window surrounds. Step Nine Make a blood sacrifice to Al. This part took us the longest. You're going to have to put the bolt through the inertial reel box, through the plastic window surrounds, through the bolt holes of the clamp, and hold the nut at the end of the clamp in place while you tighten the bolt on. Congratulations, you've got about an inch and a quarter to work with to hold it in place, and I hope you're instrument rated because you're not going to be able to see anything as the plastic is covering it. We tried several methods to do this, including using masking tape to tape the nut to the wrench itself but no matter how tightly we got it, it never was enough to hold tension for the bolt to start to thread through. Good luck, and may the Mooney gods be with you. Step Ten Once that's on, torque it to the appropriate setting (I want to say it was 70 or 90 inch pounds) and put the plastic cover back on the inertial reel. Step Eleven Reinstall the headliner, plastics, etc. into place. Step Twelve Reinstall the seat, install new cotter pin, and install the lap belt back on to the seat, then do a test fit. Crack open a cold one, sit back and admire your work, and look at your watch as you realize that just took you almost a full day. I hope you found this helpful, this was not a fun process, but I will say the passenger's side is much easier (a lot more clearance, and you can actually see!) and rest knowing your flying now just became a lot safer. Apologies for the sideways pictures, they are right side up on my computer but inserting rotated...
    2 points
  8. Yes, just be sure to pay attention to any policy limitations: horsepower, max seats, landing gear configuration, max value covered, etc.
    2 points
  9. Thanks all for your support. If any of you are (understandably) concerned about placing your business with a new agency, I'm happy to report that we were profitable as of about July 1 (6 months in business). I'm presently licensed in 50 states plus DC (most expensive startup cost). By far the best marketing dollars are Sun 'n Fun and this MooneySpace sponsorship. Thanks again, all.
    2 points
  10. Cut that little piece of tape and put it on your ASI, clean stall speed x 1.404
    2 points
  11. I suspect it wasn't so much a stall spin but collision with the high power lines almost directly above that you can see in the video and that Nick refers to above. Perhap they were maneuvering to the very nearby private airport 61VA. I wondered if it could be an instructional flight but I see the Captain's CFI expired some 35+ years ago, so probably not. But if indeed it was a collision with the power lines, something had them flying very low and the best I could come up with is the very close by private airport. Perhaps the preliminary will tell us. Wonder if the power lines have the large orange balls on them like they do out west? I couldn't tell from the satellite view.
    2 points
  12. So the best way to adjust the roll threshold is to max out the pot until it produces a slight roll oscillation and then back it off until the oscillation stops. There is a product that Bob has suggested to me and I have started using that works wonders with connector pin issues. Stabilant 22, you can find it online. I have been using it for about a year and had great results.
    2 points
  13. Winchester connectors used to have a machined 4 pin female connector that worked great but I have not been able to locate the connector for some time. Using a small pick you can push the female split pins back together. Sometimes this will fix the intermittent issues that are connector related.
    2 points
  14. MSA is published and available on charts and approach plates. The MVA is generally only known by the controllers.
    2 points
  15. And replace your alternator belt while the prop is off.
    2 points
  16. Nice pictures! That's the spring inside the cartridge that pulls in one direction. There is an external spring that pulls in the other. The springs bias the elevator as the empennage moves with the trim. Without the bungees, the trim system would have to change the incidence of the tail by a greater amount to get the same trim effect. This system was used up through the J. Skip
    2 points
  17. They seal better if dry, they go on better if they have a little lube. Lube them with a little mineral sprits or alcohol, which will dry up.
    2 points
  18. It is me José N11606. The -72 holes are about 1/4" above the bottom (well below the fuel pickup screen). I found about this on an engine failure on takeoff on my old M20C based at TJBQ on the ramp. The runway was 9,000 ft long so I Ianded on it and taxi out with the momentum. On the taxiway I drained the tanks with the old 53S valves and only fuel came out just like it did before flight when I drained them. I decided to unscrew the valves and plenty of water came out. Once the -53S nutplate drain holes are clogged they will not drain water but fuel at the top of the valve stem. The higher water accumulated level raises toward the fuel pickup when the plane accelerates and climb causing the engine malfunction. This why the malfunction does no show on the ground run up. Have been using the -72S for over 20 years with no leaks and no engine failure. The nutplate bottom drain holes can easily be plugged during tank reseal or by old sealant debris. If using the -53S make sure the drain stream is greater than yours on a palm tree, otherwise suspect a clogged nut plate drain holes.
    2 points
  19. 2 points
  20. My two cents on the subject To avoid any stains on the valve I replaced the F391-53S valve for the F391- 72 valve used on Cessnas and many others and sealed the threads. No leaks and drains better than me on a palm tree. The - 53S has the drain holes at the very bottom of the threads. It drains through the little holes on the nut plate F391-53- SMP-2. If the nut plate little holes at the bottom are easily plugged with debris or sealant the drain valve will drain fuel but no water from the very top of the stem. The -72 drain holes are just above the threads of the nut plate. So debris or sealant on the nutplate will not block the drain valve holes. Because of this you can put sealant on the threads (no need for the O-ring) to avoid leaks without impairing the draining ability. These are the same ones used in the Monroy long range tanks.
    2 points
  21. I had one of those update questions come up and almost pushed the wrong button. I don't remember the exact verbiage, but I thought it was along the lines of Update Now, Update Later, and do not update. The "Update Later" turned out to mean it would update later that night (or something along those lines). Is it possible that's what happened to you?
    2 points
  22. Hey all, Rocket Drivers especially: my 86 Rocket fresh out of paint and interior today. Good as new, faster than new (almost) but 1/4 the price! What a machine!
    1 point
  23. Hello guys here is an update: As per your advice on anonymity and knowing it would lead to possible bad area I deleted the post but didn't want to leave you hanging. As of yesterday morning the problem item you know about has been "resolved". Item in question is physically red-tagged. Thanks to everyone for their sound advice!
    1 point
  24. If you don't live in Kali, have them meet you somewhere outside the state, and it will simplify the Kali Board of Equalization tax fight for you.
    1 point
  25. I fly a J and I have found 70kts is the airspeed over the numbers for a no float landing. Short field landings are done at 65kts. This is ignoring those gusty days when you have to factor in a few extra knots. I encourage you to enroll in a MAPA Proficiency Program. Great way to really get familiar with your airplane.
    1 point
  26. SG3ASH45B Snap On part number for the probe. Stabilant 22 by all means on the connections. A health check of the servo motor should be done as well. Give a call if you would like, visit WebairConsulting.com then call 616 822 1999
    1 point
  27. Thanks, I am neither a CFI or commercial so when I fly another plane it is pleasure or business. I assume that would include moving a friend's plane to/from a maintenance shop or to ferry someones plane, w/o compensation of course.
    1 point
  28. Yes, but the coverage will typically only cover non-owned flying for the purpose of use stated in the policy. For personal pleasure and business flying, this will not cover CFI work.
    1 point
  29. My Century IIb with STEC-30 ALT is perfectly level and straight with no oscillating in heading mode. When I go to NAV mode running off of the Avidyne 440 I have a slight oscillation that I was not able to adjust out. The altitude hold works perfect if I manually trim it slightly up or down, but if I trim it perfect then turn on the STEC-30 ALT hold it hunts up and down and is uncomfortable. If it does that I turn the trim up or down slightly then is butter smooth.
    1 point
  30. Awesome thanks! It would be pretty nice to have a cleaner dash
    1 point
  31. The policy you have for your Mooney could have, or have added, a non-owned provision.
    1 point
  32. The (new to me) self darkening welding hoods are wonderful.
    1 point
  33. Hartzell Propeller Owner's Manual. Version 115N
    1 point
  34. Parker, your first point is not quite the case. While a named pilot is considered an "insured" under the policy, they do not have the same rights as a Named Insured. Being considered an insured under the policy grants them rights of protection for liability under the policy but not necessarily protection against subrogation for damage to the Named Insured's aircraft that they might be liable for. There is typically a "No Benefit to Bailee" provision in the policy. This is why your point two is sometimes contained in a policy. My thoughts, and as you've highlighted, always have a non owned policy to cover the damage to any aircraft you might be flying and/or make sure you have a waiver of subrogation in the borrowed aircraft's policy.
    1 point
  35. Nice write up. Just a suggestion ...if possible get the clamps with welded nut. Makes life much easier. If you ever have to remove the interal reel. Mine are not the the inertial reel shoulder harness but if I am not mistaken ones that I bought from lasar (I think it was lasar) had ms## clamp with the welded nut as part of shoulder harness kit. Not certain but I think the alpha harness is using the same part number. If I recall correctly the instructions on the lasar kit said that drilling a small locator was as required. I elected not to drill the hole. Minimizes any potential corrosion. Looks like painted yours which is better but you still have dissimilar metals between screw and tubing structure. Just my personal preference. James '67C
    1 point
  36. Back in the day... community barn raising... Today... online community hangar restoration..! A great excuse to buy some harbor freight welding equipment, and real safety eye and face protection to go with that... Review the thread about getting an unintended sunburn from an unprotected UV source... Best regards, -a-
    1 point
  37. it was a pain cutting the safety wire off, it's his job to put it back....lol
    1 point
  38. Yes, DC-4 is used, but engine oil is acceptable also. I should clarify that my lubricant information comes from my local propeller shop.
    1 point
  39. My experiences...... please do lubricate new O ring fully prior to installation into hub. Fresh engine oil as a lubricant will be fine.
    1 point
  40. Engine oil is fine. Both the “o” on the prop flange and the “O” on the flywheel should line up. The flywheel should only fit one way. who didn’t index it? Lol. -Matt
    1 point
  41. 1 point
  42. Well, where do you have automatic updates turned off? There are at least two places where you can do something like that. One is in Settings>iTunes & Apps, there are a couple of buttons there, where you can turn off App updating, or Automatic Downloads of cell data. The one that counts the most is in in Settings>General>Software Updates, where there is a menu item to enable or disable automatic updates. That one should be off. I also keep the Automatic Downloads of cell data off in Settings>iTunes & App Store. I don’t have a problem with my iPad downloading OS updates with those settings. I just checked, Settings>General>Software Updates says I still have not downloaded 13.1.3 . I also usually keep Settings>Cellular Data off unless I have a reason to use the cell connection to download something. If you leave it on and the iPad makes its own choice, you can wind up downloading too much data and blow through your monthly account limit. That would also prevent your iPad from using the cell connection to autodownload an OS update. Don’t know the answer for sure, I just know I don’t have the problem on my iPad.
    1 point
  43. Of everything I see out there,this would be my choice: https://www.controller.com/listings/aircraft/for-sale/155264785/1997-mooney-m20m-bravo Only issue I see here is the 430w. They have everything you need but not sure about indefinite support... Also, I’m no aircraft appraiser but considering the 430’s and everything else, feels like there is some room in the price. Yes, those aspens aren’t cheap but neither are 750s and 650s. Don’t want to be selling the equivalent of a KLN-94 to someone else if you want to get out of the plane in the next 3-4 years.
    1 point
  44. Regardless, RH is at its peak just below the cloud bases . . . .
    1 point
  45. USAIG is a good company with good claims service. So are Old Republic (I used to work for them as an underwriter) and Starr.
    1 point
  46. Thanks. The slide button to automatic updates is turned off yet it still updated on its own. I have a message on the Apple Forum Community right now but no one has responded. It is really not that big of a deal other than I have an issue with computer devices taking on a sort of AI and doing things when I have clearly stated I do not want them to be done. Apple seems to be the main offender. They feel they know what is right for you and your device and do it without asking. My android phone is now getting to be that way with Google.
    1 point
  47. The loss you describe is unlikely, but it is not unreasonable to want the person providing training to have their own insurance coverage. You will just have a smaller pool of CFIs to provide services to you. You'll also have to note your policy will pay out first and they'll subrogate (if they can) on the CFI's policy. So you'll have a bad loss ratio for awhile. This is because the CFI's policy is only going to pay out if legally responsible or if the insurance company wants to settle, knowing their client is responsible for the occurrence. I would accept this kind of legal and financial risk as a CFI as long as I knew my services were keeping within the terms of your insurance policy. But it is also entirely reasonable for the CFIs here to go about their risk-averse strategies.
    1 point
  48. Alex, Ill show you a nice scar on my head at the Summit where it was stapled back together. Did I mention I was wearing a shoulder belt? Without it, I wont be here typing. Hopefully, you will realize the few $ spent on shoulder belts are a far better addition to your plane than some new headset or other gizmo. Personally, I wont fly in any aircraft that doesnt have them.
    1 point
×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.