Jump to content

Leaderboard

Popular Content

Showing content with the highest reputation on 12/23/2016 in all areas

  1. Got out to BDR to visit my family for a couple of days before Christmas. The Mrs was going to be stuck at work all week, so it was just me and the little one. It's something special when talking to NY approach and getting the rapid fire questions from the three year old (where is the airport? Why we not going down? Etc.). Fun flight with a great tailwind. I pulled it way back to 2300/ 7.2 GPH / 140ktas just to see the nmpg hit 24.3. But I missed seeing 185 it's ground speed and wasn't sure how long toddler would last before I'd need to put her in "isolate", so back to ROP for the last hour or so. Apologies for the ugly door. I still haven't made my new decorative pieces. I finally got my basement composites setup going - repairing my landing gear fairings. Sent from my iPhone using Tapatalk
    5 points
  2. Why wouldn't I want to listen ----- Because I have to listen to every conversation on ATC After 30+ yrs I'm tired of the noise What if I have trouble? That's why I carry an InReach SAT radio, on and tracking on every flight. It gives a far better location than any ATC can. 1 button push and help is on the way to a WAAS location transmitted to them AND they see the track with altitude going down on their end. They start the Cavalry ! Like right now! If I'm not going down ATC can't do anything for me that I can't do for myself. I'm way out west, you have to look hard to even find any traffic, back east maybe I'd have a different thought process I go to Dallas often and use Approach Control BUT even when VFR you ALWAYS get routed way around the airspace as a little guy. It's just their thing. KABQ does the same thing, miles out of the way for no reason than to keep you away. Now, ADSB In might be a God send even for me, we'll see what the next couple of years have to offer after what I saw at Oshkosh this last summer.
    4 points
  3. I went out to the hanger earlier this week to finally empty out the mini fridge for winter. Everything was froze solid except a few bottles of water. It was fun playing with, but makes me wonder why I live in Minnesota. -Dan
    3 points
  4. Sorry for the retread from last year, but I didn't have time to photoshop another Mooney in flight over a winter scene. The feelings are unchanged.
    3 points
  5. It ain't the model, that's nonsense. What does your MAP read with the engine not running? You should get within a inch or so of that on full throttle take off once you get rolling. That's a take off roll "call out" item for many of us. Along with fuel flow (~ 18 GPH for your IO360) and ASI coming alive.
    3 points
  6. http://www.avweb.com/avwebflash/news/NTSB-Controller-Error-Led-To-Midair-Collision-228246-1.html The NTSB also noted that the cockpit views and surrounding environment made it difficult for the pilots to spot each other until it was too late to avoid a collision, and neither aircraft had traffic detection equipment. The board recently issued recommendations for additional training for controllers based on the accident and a safety alert for pilots to promote the use of traffic displays. José
    2 points
  7. My 84k, 231, with less than 180 SMOH has been a good, reliable plane. Rarely do I have any oil leaks, and if I notice something small, it gets tightened so no more leaks. Two flights ago, I noticed a bit of oil on nose gear door so I did some snooping and it looked like it was coming from the turbo check valve. I talked to the mechanic and he thought it was coming from above there, on the accessory case (Not sure if that is the term, but right above the oil filter) and collecting on the check valve. He tightened the accessory case and the check valves and off I went. The next flight, about .4 hours, there was MUCH more oil on the nose gear doors, on the nose gear and all over the check valve/oil filter area (Accessory looked clean). So I parked it where it was and had a mechanic look at it Monday. It appears the adel clamps were loose, allowing movement and chaffing on the supply side turbo check valve, under the clamp. The chaffing causing two tiny pin size holes in the casing of the check valve. Hot oil squirting all over. Very little actual oil was lost, pressure and temperature never varied (Probably a couple of tablespoons of oil at most). So, 231 owners, check your adel clamps on the turbo check valves and make sure they're snug, there shouldn't be any play for the check valves to move around. I think there was a SB about Dukes check valves, but I'm pretty sure these are not them. $500 for a new check valve... Edit: I just called Top Gun (MSC) and they said those adel clamps should be inspected and changed every year...
    2 points
  8. Logged another 5 hours on the plane today. After 8 hours in the Bonanza yesterday doing a very long Airlifeline flight, my back side is pretty sore. Caught Chad, my local FBO owner, flying chase plane to KSAW to retrieve a pilot dropping off a Conquest his shop just worked on. I talked him into taking some air to air photos of my new ride on their way back. Pretty neat! Tom
    2 points
  9. Hey guys I just got off the phone with Insight and they claim the G2 can interface with this generator. It is just a single cylinder so you only get EGT/CHT for one. I'll call up Mike Busch later and ask if we can upload data to Savvy Aviator for analysis. Sent from my iPhone using Tapatalk
    2 points
  10. Anyone interested in a set tire chains? I just bought a two-pack for $40 shipped. Has the "v" teeth. Huge difference on ice. Sent from my iPhone using Tapatalk
    2 points
  11. Joyeux Noël et bonne année!
    2 points
  12. I have an ez 35 with the transmission and it apart last week. Very simple inside and I had the same problem a couple of years back. The shaft that goes though the transmission has a divet on the shaft that a small metal biscuit fits into, mine popped out as a result of me moving the forward reverse lever to aggressively. If this is your problem the small biscuit might be floating in all the gease inside the transmission, so you will have to look for it. Placing back in the proper order is a bit of a puzzle, but it wasn't,t a difficult job.
    2 points
  13. A PCV is like having a hose to inhale your own flatulence.
    2 points
  14. After it happens 5 trips in a row, you know it is SOP. They are trying to vector you and its because it makes their life easier. I typically go along with it since ts a minor inconvenience that adds 5 or 6 minutes to my trip. I do so because I'm convinced Austin Tx will be the next class B and I'd like to see that delayed as long as possible. Austin has over 106,000 commercial operation a year. Or roughly the same volume as St Louis or Kansas City, and more than Cleveland.
    2 points
  15. 1DH has been sold, closed and delivered to its new owner as of 12/22/16. Great guy from Austin, TX looking for something faster, efficient and in great shape. Hope to see him lurking around the forum in the future. I will miss her but the twin has arrived and now the family will fly with me, finally!!
    2 points
  16. Golf? We XC ski in the Great White North. This is behind my house last night skiing on the frozen river.
    2 points
  17. I have to echo this. From the first time I was on this site I felt like I had found a home and after getting my PPL a couple months ago and my Mooney a couple weeks ago I'm here to stay. Merry Christmas!!
    2 points
  18. First Post! Hello all. I am an Apache Helo pilot for the Army. I love flying. Last few years I have been fighting off an urge to start flying general aviation. I have decided to give up and give in because I see the urge is not going to go away anytime soon and is now becoming part of who I am. I want a plane that has the best bang for the buck when it comes to cost of ownership and performance. So, I've pretty much set my eyes exclusively on Mooney. I love the way they look and the numbers look pretty good too. I hold a commercial rotary wing with instrument license, and since I am an Army instructor pilot, I also am interested in completing a commercial fixed wing license and possibly get into the CFI and/or CFII world. I'd love to be able to teach my family and friends but that's about the extent....I'm not interested in teaching for hire anytime soon. Anyhow. I have read threads on this forum that talk about using a Mooney as a trainer and there are differing opinions. I feel I am in a much different situation than most beginner pilots having 2700hrs in the Apache (which is a beast of complexity). That being said, I know airplanes are way different and my control touch will not immediately transfer over to a Mooney. I think I'll beat on a Cessna with an instructor for about 2-5hrs before instruction in my "new to me" Mooney. Anyways, I'm new here. Feel free to tell me my plan is not a good one. I am open to suggestions.
    1 point
  19. Does the plane have a current annual from either of them? I'm personally would go to opposite shop if they do.
    1 point
  20. That's ok ,with all that flood damage,I bet there will be lots of residential home improvement projects financed by flood insurance or Thames water!You may end up with a turbine if successful bidder on enough projects!
    1 point
  21. Thanks, Anthony. That was a good explanation of GAMI spread, I wasn't using the term correctly. Learned something new that I thought I'd understood!
    1 point
  22. The choice is simple. Both will do the same job. both very thorough. Laser will cost twice as much as top gun. Your choice.
    1 point
  23. Yes and know... Even a carbed engine has a 'Gami spread' as one cylinder will peak before the others during the Leaning process. A FF meter would be required to measure the spread. The roughness occurs as one approaches and peaks before the others. The real roughness occurs as one cylinder starts missing on the lean side. An engine monitor would be important to see how this is occurring... There are a few things that affect the spread like MP, altitude, throttle plate position, carb heat, mixture, the secondary fuel jet, OAT. These are the things that can influence the distribution of fuel. Unfortunately, there is no four barrel carb for the M20C. We would be balancing fuel jets with precision. Yes you could sort of measure a gami spread on a carbed engine, with FF and JPI. But improving the spread is quite a challenge. Happy experimenting... Best regards, -a-
    1 point
  24. We scrubbed last night. We are going tonight.
    1 point
  25. If you have a fuel flow meter and engine monitor, it is not difficult. Without them, I think it is impossible.
    1 point
  26. I could easily be wrong, but it would seem odd to me that the air/oil separator would "coke" up. Gunk up, yes, but I would expect you could take one off and with some effort, clean it out. I can't believe they would have a life limit.
    1 point
  27. My Continental ran smoother after GAMIs installed, and meets their recommended GAMI test criteria. I would suggest you run the GAMI test, and if you are within the prescribed range, (or if you can get within the range by swapping your own injectors) don't buy them. If not, buy them and install. Run the test again. If they don't get within the range, GAMI will customize them until they do. If my memory is correct, your fuel flow should not vary by more than .5 gal/per hour from the first cylinder to peak until the last one. But check GAMI's site. If you are lucky, you can get closer than that.
    1 point
  28. Well after about 4 hours practicing maneuvers and a bit of studying for the oral, I passed my commercial check ride! I was stressed as usual for a check ride but honestly my examiner was awesome! He made it fun! Thought I'd share my accomplishment with ya'll! Mike
    1 point
  29. I don't have my performance books near so I can't get true numbers but all that goes out the window if they are overweight. A little temp rise, a little extra weight (from "guesstimated weights) and you get into trouble if you are runway limited. The plumes you see at the wingtips in the turn are from fuel dumping. It tells me they knew they had a problem, maybe an engine problem. If they were airborne and climbing even slowly they wouldn't need to dump (unless terrain intervened). Why they were in the turn I have no idea. Basic aerodynamics, you lose lift in a turn (wingspan). Just as an aside on the old 727-100s- The tailskid was electric driven. If it didn't retract on gear up it affected range by (IIRC) 14% !! On corporate, long range 727-100s way back when, if they were going over water it was sometimes known to pull the CB for the tailskid before landing (keeping it up on gear down) so that on the next takeoff for the over water leg it wouldn't be extended and possibly fail and suffer the drag penalty thereby not being able to continue on the over water trip where you needed that range.
    1 point
  30. Yes. Plastic putty knife though. Work slowly to de-bond it to avoid bending inspection plate. When installing be uber careful to not get sealant into the nut holes or they'll pop off. Not a problem at the time but will fall away next time you go in. -Robert
    1 point
  31. Let me know when you're ready, thinking about selling my C next year to finish my RV-8 Sent from my iPhone using Tapatalk
    1 point
  32. They did it to Hans Solo, and they got him restarted again.
    1 point
  33. So how does this help me decide whether camguard will make a difference?
    1 point
  34. It's interesting to see how some people's priority isn't the dollar value of the plane as much as it is the ability to fly the plane. this can happen when 50% or 25% of the asset isn't a giant chunk of the owners other assets. 25% of a 50AMU plane. 12.5 AMU 50% of the same plane is 25 AMU Once your house is paid for, kids have moved out and retirement plan is in place, the unevenness of the capital put into this plane is small for a guy that has good partners... This is my understanding of how a good partnership can be used. Some good partners may be more financially sensitive. Some less... when seeking partners, consider getting an engineer, a pro pilot, and a third talented person from another area.... like someone good with finance and accounting.... Best regards, -a-
    1 point
  35. Hi guys, apologies about lack of communication, its xmas time and the residential construction industry goes a bit haywire at this time of year. Everyone wants their houses finished before the 24th. I have no idea why, personally i think they are just being fussy! Update time again though. (Ill post pics later today). However after the condition report showed a few areas for manitenance, we decided to do everything on the report, so the bushels in the nose gear, brake cylinders, and aileron hinge plates are all being replaced. Just waiting on parts now, I just hope the msc has ordered them direct and not through Troyes in France for they take forever to get things to you. Both tanks have been cleaned and resealed. Gami injectors are in. All corrosion has been removed and chemically treated to stop it. All measurements checked and well within tolerances. All access panels have been cleaned, primed and resealed. Aircraft has been "neutral washed" to remove any chemical residue and is now drying over the Christmas break. The interior is back with us from Aerocomfort. I havent seen it yet, but the guys say it is all there and they havent opened it to avoid "getting sticky toffee fingers on it". I do love how non English speakers translate their phrases into English. In the New Year she will have her primer put on her, then ill go and visit to see how she is. I feel i can see the light at the end of the tunnel. Andrew
    1 point
  36. As someone who does not have a single legacy instrument, the thought of not having a certified backup in the panel is enough to give one goose bumps. The one benefit of having multiple instruments like the 6 pack as backups is having multiple instruments as backups. An iPhone or iPad as backup--NO WAY.
    1 point
  37. Never had that problem, but then those of us whom crab and kick have to be quick on their feet ;-)
    1 point
  38. Cross wind landings won't put side loads on the Johnson bar. If your preloads are correct it should put no loads on the actuation mechanism. It will put loads on the overcenter links on the main wheels, but unless they come off of overcenter, which they should never do, no load will be transferred beyond that.
    1 point
  39. The announcement of the KI300 has been the cause of many to drink the vaporware Kool aid here, and even one particular evangelist to quote the high reliability of this non existent product. Once I heard RC Allen had a "hand" in its' development and production, my hopes of it being viable were greatly diminished. see https://mooneyspace.com/search/?&q="ki 300" While in theory, the KI300 would be nice, what would be even nicer is an option for the ESI 500 to drive the antiquated analog KI autopilots. Those "fine swiss watch" KI 25X AI's are making Bob Bramble have a very nice Christmas once again, and will continue to do so (currently at about $2500/ rebuild and align every 500 or so hours). Nothing against Bob, he does a great job on filling this demand.
    1 point
  40. I always was wondering how I could explain these to my wife.
    1 point
  41. Transponder is back in and working. We found that the backlight was the one run to the new circuit breaker. The actual power to the transponder was just a dead end, possibly taken off the bank of fuses we removed. New PAI-700 vertical card compass is installed. We will swing that later. Waiting on the holidays to go by so my IA can come and put this governor back in. Hector, Hijackers is on our shortlist. We might be working on it the 25th, so maybe soon afterwards. Upcoming destinations: Jan 14- KLEE for the Florida Mooney Breakfast. Jan ~21: Poss Charleston, SC to visit the USS Yorktown Feb: The missus and I want to fly to Kitty Hawk, NC to see the Wright Bros memorial. I've been there as an 8 year old, I'd love to go back and get a picture in the same spot. March: Tullahoma, TN for the Beech museum April: SnF & Wings Over Suwannee July: OSHKOSH!
    1 point
  42. Feliz Navidad Y Prospero Ano Nuevo
    1 point
  43. Way to go Don! Let's get the festivities started! Merry Xmas, Happy Hanukkah, and pleasant holidays to all who are celebrating this time of year... Best regards, -a-
    1 point
  44. I just purchase one of these from PowersportsMax a youth sized ATV 125cc 4 stroke motor, Electric start, forward and reverse, auto trans. I purchased a much small front sprocket. I have a bogert tow bar and have rigged up the atv with a 2" receiver. I'm all in for a little over $700 including shipping. I have a floor mounted winch to pull the plane back into the hanger. I only have trouble pulling the plane out in the winter over ice. But my FBO charges to pull the plane to the maintenance hanger for service or O2. I was looking for something that would actually be able to go the distance with ease.http://www.powersportsmax.com/product_info.php/cPath/37_99/products_id/20655I
    1 point
  45. As you know there is a bit of skill in landing things... solo in a trainer... fly the mooney
    1 point
  46. I can't fly in the flight levels until out of Phase 1 testing (40 hours and I am at 18.6 now). The speed limit is a real concern, especially since on descent you are carrying more speed as well. I find it something I have to watch closely and work at. The good thing is the limit is IAS, not ground speed. Tom
    1 point
  47. I had an M20 oil separator for 10 years and really happy with it. As others mention it has to be properly installed for good performance. Most important is that the intake has to be above the case vent port. Mine has the oil drain to the bottom side of the #4 valve cover. The exhaust is connected to the original line. There was 1/4" side hole on the line that I plugged. I found that the hole needs to be plugged for optimum performance. The hole is a backup for in case the vent tube is iced. I think this is more of a myth since the vented vapors are at least 100F with no chance for icing. I can fill to 8qts with no belly stains. Oil consumption is about 1qt/9 hours. There is no filters or screens inside M20. It is just two pieces of coaxial pipes inside. It works on the principle of vapor condensation and gravity. The condensed vapors are accumulated on the outside container and later discharged to the engine when is off. If the oil content on the vapor is too high or the trip too long it may exceed the outside container and it may start discharging on the exhaust port. For optimum condensation the M20 must be away from hot spots in the area. The only maintenance on the M20 is flushing it with MEK to keep the drain port clean. José
    1 point
  48. FWIW, My "F" is currently at CE Avionics @KSFB. I was the high bidder on the Lynx NGT 9000 at Mooney Summit and it is getting installed. I am also having my KLN 89B changed out to a KLN 94, my #2 radio moved to the right panel, my ADF and related accessories removed, vertical card compass and USB charging port installed and a lazy AI repaired. My experience so far has been a good one. Robert Powell is the salesman, a retired pilot and most professional. Their hourly rate is $105 but I have learned it is sometimes less expensive to pay for experience than to pay for someone to learn. I received a detailed estimate and will report back after the work is completed.
    1 point
×
×
  • Create New...

Important Information

We have placed cookies on your device to help make this website better. You can adjust your cookie settings, otherwise we'll assume you're okay to continue.